Determine exit temp of oil and heat transfer rate between

Assignment Help Mechanical Engineering
Reference no: EM13618402

Consider a shell and tube heat exchanger which is used to heat water (Cp, water = 4.33kJ/(kgK)) from 10 deg C to 85 deg C flowing in the tube at the rate 7kg/s. For heating of water, hot oil (Cp, oil = 2.34 kJ/(kg*K)) is used which is flowing in the shell at the rate 14 kg/s and enters the heat exchanger at 155 deg C. Determine exit temp of oil and heat transfer rate between oil and water. Consider water and liquid as incompressible liquids and heat exchanger as very well insulated.

Reference no: EM13618402

Questions Cloud

A circuit consists of a resistor in series with an : a circuit consists of a resistor in series with an inductor and an ac generator that supplies an rms voltage of 115 v.
Triplette corp began the year 2008 with -5 million in : triplette corp. began the year 2008 with -5 million in retained earnings. the firm earned net income of 10 million in
A 10kg hammer strikes a nail at a velocity of 81ms and : a 10kg hammer strikes a nail at a velocity of 8.1ms and comes to rest in a time interval of 8.5ms . what is the impulse
Caps corp reported sales for 2008 of 45 million caps listed : caps corp. reported sales for 2008 of 45 million. caps listed 9 million of inventory on its balance sheet. using a
Determine exit temp of oil and heat transfer rate between : consider a shell and tube heat exchanger which is used to heat water cp water 4.33kjkgk from 10 deg c to 85 deg c
A box is lowered by a rope at a constant speed if its mass : problem 1 a box is lowered by a rope at a constant speed. if its mass is 20 lb its downward speed is 3 fts and the
Wills wheels inc reported a debt-to-equity ratio of 65 : wills wheels inc. reported a debt-to-equity ratio of .65 times at the end of 2008. if the firms total debt at year-end
Determine total change in enthalpy of the gas of amount : consider a thermal insulated closed rigid tank which is divided into two parts a and b by a partition. initially part a
Consider the following three bond quotes a treasury note : consider the following three bond quotes a treasury note quoted at 10230 a corporate bond quoted at 99.45 and a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd