Determine athe force sustained by the matrix phase bthe

Assignment Help Mechanical Engineering
Reference no: EM13634469

A continuous and aligned fiber-reinforced composite having a cross-sectional area of 1130 mm^2 (1.75 in.^2) is subjected to an external tensile load. If the stresses sustained by the fiber and matrix phases are 156 MPa (22,600 psi) and 2.75 MPa (400 psi), respectively; the force sustained by the fiber phase is 74,000 N (16,600 lbf); and the total longitudinal strain is 1.25 10^ -3, determine: (a)the force sustained by the matrix phase, (b)the modulus of elasticity of the compos- ite material in the longitudinal direction, and (c) the moduli of elasticity for fiber and matrix phases.

Reference no: EM13634469

Questions Cloud

A 01 muf capacitor is to be constructed by rolling two : a .01 muf capacitor is to be constructed by rolling two strips of 10cm wide metal foil with a 1 mm thick paper layer
For which wavelenghts of visible light does destructive : a soap lm nf 133 is 465 nm thick and lies on a glass plate ng 152. sunlight whose visible wavelengths in vacuum
A material that you are working with has a band gap of 4 ev : a material that you are working with has a band gap of 4 ev but it is opaque doesnttransmit light because it contains
Calculate by explicit summation the vibrational partition : calculate by explicit summation the vibrational partitionfunction and the vibrational contribution to the molar
Determine athe force sustained by the matrix phase bthe : a continuous and aligned fiber-reinforced composite having a cross-sectional area of 1130 mm2 1.75 in.2 is subjected to
Term coeff secoeff t-ratio p-value intercept 23979345 : examine the regression 90 confidence interval 90 prediction interval using 1990 and 2004 energy use kg oil equivalent
You produce an image of the sun on a screen using a thin : you produce an image of the sun on a screen using a thin lens whose focal length is 23.0 cm. what is the diameter of
Determine for the cycle a the mass flow rate of steam : water is the working fluid in a regenerative rankine cycle with one closed feedwater heater and one open feedwater
A rod extending between x0 and x140 cm has uniform : a rod extending between x0 and x14.0 cm has uniform cross-sectional area a9.00 cm2. its density increases between its

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The coefficient of kinetic friction between the brake pad b

the 50-kg flywheel has a radius of gyration about its center of mass of ko 250 mm. it rotates with a constant angular

  Consider the power system as designed below the duty fluid

consider the power system as designed below. the duty fluid is water and has a mass flow 0.75 kg s and all piping

  Calculate the ultimate tensile strength

Calculate the ultimate tensile strength (engineering) of a material whose strength coefficient is 700 MPa and a tensile test specimen which necks at an engineering tensile strain of 0.35.

  Determine the concentration of carbon in an iron-carbon

determine the concentration of carbon in an iron-carbon alloy for which the microstructure consists of proeutectoid

  Estimate the percentage of fabric samples that will have a

data analysis of the breaking strength of a certain fabric shows that it is normally distributed with a mean of 300 lb

  To remove the organic gases and the particles the flow is

in the production of ethanol from corn the solids left after fermentation are dried in a continuous-flow oven. this

  Calculate the rate of heat removal kw required using the

liquid ice cream mix is cooled frozen and hardened from 4degc to -20degc at a rate of 10000 kghr. calculate the rate of

  A big fireplace can be approximated as 15 m3 of volume its

a big fireplace can be approximated as 1.5 m3 of volume. its made of firebrick with properties ? 2600 kgm3 and c 950

  The speed is then held constant for 198 s after which there

an automobile accelerates from rest at 2.2 ms2 for 24.6 s. the speed is then held constant for 19.8 s after which there

  Please use ees to solve this problemone method for storing

please use ees to solve this problem.one method for storing hydrogen involves cooling it so that it liquefies. figure

  If the minimum power into the compressor is 3 kw and it has

air flows at a rate of 0.01 kgs through an adiabatic compressor. the gas enters at 100 kpa and 20oc. if the minimum

  Now the valve is opened and the entire system is allowed to

a 2 m3 tank containing nitrogen at 25oc and 500kpa is connected through a valve to another tank containing 3kg of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd