Solution-Determine an equation for the efficiency of the

Determine an equation for the efficiency of the gear train

Assignment Help Mechanical Engineering

Reference no: EM13550004

QUESTION 1

A pulley 150 mm diameter is driven directly by an electric motor at 250 revs min-1. A V-belt is used to transmit power from this pulley to a second pulley 400 mm diameter against a load of 200 Nm.

The distance between the centre of the pulleys is 600 mm, the included angle of the pulley groove = 40°, the coefficient of friction between the belt and pulley is 0.4 and the ultimate strength of the belt is 8 kN.

(a) Calculate the actual power transmitted to the second pulley.

(b) Calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

(c) What would be the effect of the following factors on the maximum power which can be transmitted (give reasons for your answer):

(i) increasing the coefficient of friction

(ii) increasing the included angle of the pulley groove.

(d) What would be the effect on the following if the load torque is increased and the speed maintains constant (give reasons for your answer):

(i) the tension in the tight side of the belt

(ii) the tension in the slack side of the belt

(iii) the power transmitted.

QUESTION 2

A gear train is to be designed to transmit power from shaft 1 to shaft 2 with the following condition:

(i) Shaft 1 (driven by an electric motor) rotates at 100 revs min-1.

(ii) Shaft 2 is to rotate at 400 revs min-1 in the opposite direction to shaft 1 against a load of 200 Nm.

(iii) The centre of shaft 1 is 300 mm from shaft 2.

(iv) The minimum number of teeth on any gear is 15, all gears must have a multiple of 5 teeth and have a module of 2 mm.

(v) The maximum number of gears permissible is 4 gears and the diameter of the maximum gear must be minimized.

(vi) The centers of the gears should lie on a line which is as close to straight as possible.

(vii) All shafts have a frictional resistance of 5 Nm. Carry out the following:

(a) Design a gear train which satisfies the above criteria. Use a sketch to illustrate your design, label the gears A, B, C, etc. from the driver to the driven gear, and state the number of teeth on each gear.

(b) Determine the input power required at shaft 1.

(d) Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 (all other factors remaining constant).

Reference no: EM13550004

Questions Cloud

Explain the gulf coast of louisiana and mississippi : Hurricane Katrina, which hit the Gulf Coast of Louisiana and Mississippi on August 29, 2005, had the second lowest ever recorded barometric pressure at 920 mb.

Determine what is the magnitude of the resultant force : A 13.0-kg object undergoes an acceleration of 1.5 m/s^2. What is the magnitude of the resultant force acting on it

Find the speed of the electron and speed of the proton : The rest energy of an electron is 0.511 MeV. The rest energy of a proton is 938 MeV. Assume both particles have kinetic energies of 1.80 MeV. (a) Find the speed of the electron. c (b) Find the speed of the proton. c

Define what mass can the balloon lift at sea level : What mass can the balloon lift at sea level, where the density of air is 1.22 kg m-3. What would be the payload if He were used instead of H2

Determine an equation for the efficiency of the gear train : Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 (all other factors remaining constant).

Calculate average force does the punter exert on the ball : A football punter accelerates a football from rest to a speed of 8 m/s during the time in which his toe is in contact with the ball (about 0.26 s). what average force does the punter exert on the ball

Speed of spacecraft as measured by earth-based observer : A spacecraft with a proper length of 250 m passes by an observer on the Earth. According to this observer, it takes 0.780 µs for the spacecraft to pass a fixed point. Determine the speed of the spacecraft as measured by the Earth-based observer. c

State a gas sample is connected to a closed end manometer : A gas sample is connected to a closed end manometer. the difference in mercury levels in the two arms is 115mm. what is the gas pressure in torr if the atmospheric pressure is 750 torr

Find the magnitude of the deflection on the screen : An accelerating voltage of 2.52 x 10^3 V is applied to an electron gun, What is the magnitude of the deflection on the screen caused by the Earth's gravitational field

User Account

All Pages

Determine an equation for the efficiency of the gear train

Reference no: EM13550004

Reference no: EM13550004

Questions Cloud

Reviews

Write a Review

Mechanical Engineering Questions & Answers

A l-shaped bracket lying in a horizontal plane supports a

A homogeneous cylinder with weight g and radius r lay on a

Knowing that the tank contains compressed air under a

Write a paper on boyle''s law

At this point the piston is locked with a pin and

The vessel volume is 15m3 and a standard six-blade open

What is the approximate magnetic field b on the axis

Use the depriester chart

Explain modulus of elasticity

Two previously undeformed cylindrical specimens of an alloy

How to calculate rupture point of a sample

Presuming that the bomb is perfectly insulated

Assured A++ Grade

Academics

Major Subjects

Majors

Get In Touch

TERMS & POLICIES

HELP & SUPPORT