Determine an appropriate value for the rods diameter to

Assignment Help Mechanical Engineering
Reference no: EM13613240

An engineer determines that a 40-cm-long rod of 1020 grade steel will be subjected to a tension of 20 kN The following two design requirements must be met: The stress must remain below 145 MPa, and the rod must stretch less than 0.125 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. Round up to the nearest millimeter when reporting your answer.

Reference no: EM13613240

Questions Cloud

Tundra electronic company sends appliances to dealers on a : tundra electronic company sends appliances to dealers on a consignment basis. the selling price per unit is 920 and the
The system contains a sharp-edged entrace 6 threaded 90 : a liquid at 10 c kinematic viscosity of 1.30710-6 m2s is to flow from a roof-top reservoir to a tanker truck through a
What time interval is required for the woman to travel the : a moving beltway at an airport has a speed v1 and a length l. a woman stands on the beltway as it moves from one end to
The charges to work in process-assembly department for a : the charges to work in process-assembly department for a period together with information concerning production are as
Determine an appropriate value for the rods diameter to : an engineer determines that a 40-cm-long rod of 1020 grade steel will be subjected to a tension of 20 kn the following
The athlete is able to rotate the ball at the rate of 848 : an athlete swings a ball connected to the end of a chain in a horizontal circle. the athlete is able to rotate the ball
The following information concerns production in the : the following information concerns production in the forging department for september. all direct materials are placed
Graphically determine the location of a fixed pivot for a : a link containing points a amp b must assume the positions listed in the table for each problem. below graphically
What is the ratio of the final surface charge density of : sphere 1 with radius r1 has positive charge q. sphere 2 with radius 7.0r1 is far from sphere 1 and initially uncharged.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A 644 kg steel ball is at a height of 812 meters above the

a 6.44 kg steel ball is at a height of 8.12 meters above the floor traveling at a velocity of 4.69 ms and has an

  Determine the heat exchange between the first to the second

two refrigerators are arranged in series. one of them receives 300 kjcycle from a reservoir at 300 k. the heat

  The bike is seldom used what load rating should be used to

suppose a pair of rolling element bearings is being considered as the support for the front wheel of a bicycle. the

  Estimate the infiltration flow rate

Estimate the infiltration flow rate if the window is partially open (assuming the window open area is 2 meter squared).

  What delta v was required

A satellite changes its orbit inclined 66 degrees at 260.0 km altitude to a polar orbit at the same altitude. What Delta V was required?

  Determine the amount of gypsum created from the capture and

determine the amount of gypsum created from the capture and conversion of sulfur during copper production from copper

  Calculate the minimal round-trip time delay

Calculate the minimal round-trip time delay for a radio communications link between Los Angeles and the satellite.

  Calculate the concentration of vacancies in pb

Calculate the concentration of vacancies in Pb at its melting temperature of 327oC. Assume an energy for vacancy formation of 0.55 eV/atom. Lead has an atomic weight of 207.2 g/mol and a density of 11.35 g/cm3.

  Calculate the volume flow rate of water if the pressure at

water at 80f is flowing from a to b in a 3-in coated ductile iron pipe. point b is 20ft higher than a and the total

  1 write a program that takes the image tracksjpg and finds

1 write a program that takes the image tracks.jpg and finds canny edges and then finds lines in these edges using the

  Water enters at 140degc and 20 mpa and leaves at 600degc

a steady-flow boiler is essentially a long heated variable-area duct with liquid water entering at one end and steam

  Calculate the number of miles the airplane traveled

An airplane was moving with a velocity equal to 300 mph when the velocity was increased with uniform acceleration to 600 mph in 5 min, calculate the number of miles the airplane traveled during that interval of time.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd