User Account

All Pages

Determine a the temperature of the refrigerant exiting the

Assignment Help Mechanical Engineering
Reference no: EM13631268

Refrigerant 134a at -10°C, 1.4 bar and a mass flow rate of 280 kg/hr enters an insulated compressor operating at steady state and exits at 9 bar. The isentropic compressor efficiency is 82%. Determine (a) the temperature of the refrigerant exiting the compressor, in °C (b) the power input to the compressor, kW and (c) the rate of entropy production kW/K. The surrounds can be taken to be To= 20°C, Po = 100 kPa.

Reference no: EM13631268

Questions Cloud

Design a process to produce a 05 cm-diameter steel shaft : design a process to produce a 0.5 cm-diameter steel shaft having excellent toughness yet excellent wear and fatigue
Water vapor at 6 mpa 600c enters an adiabatic turbine : water vapor at 6 mpa 600?c enters an adiabatic turbine operating at steady state and expands to 10 kpa. the mass flow
Estimate the spacing between the two irrandiance maxima : estimate the spacing between the two irrandiance maxima closest to the geometric of a plain wave illuminated
Determine the concentration of carbon in an iron-carbon : determine the concentration of carbon in an iron-carbon alloy for which the microstructure consists of proeutectoid
Determine a the temperature of the refrigerant exiting the : refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
You are to design and produce a 2 inch thick steel wear : you are to design and produce a 2 inch thick steel wear plate for a rock-crushing unit. to avoid frequent replacement
An ideal reheat rankine cycle with water as the working : an ideal reheat rankine cycle with water as the working fluid operates the inlet of the high-pressure turbine at 8000
As used in the laws of reflection and refraction what is : 1 as used in the laws of reflection and refraction what is the definition of the normal direction?2 the refraction
Draw the p-v and t-s diagrams of the cycle and determine a : a variable specific-heat air cycle in a closed system is composed of the following four processesprocess 1-2 isentropic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Does this flow satisfy the continuity equation find the

an incompressible velocity field is given byuurthetazurrthetazuthetarthetazuzrthetaz1-1r2costheta -11r2sintheta 0adoes

  Consider a 24-kw hooded electric open burner in an area

consider a 24-kw hooded electric open burner in an area where the unit costs of electricity and natural gas are 0.10kwh

  A pipe is sealed at the top and is submerged in water it

a pipe is sealed at the top and is submerged in water. it is then drawn upward from the water. how tall could the

  Compute the number of kilograms of hydrogen that pass per

compute the number of kilograms of hydrogen that pass per hour through a 5-mm thick sheet of palladium having an area

  What size unf bolt made from sae grade 5 steel is needed to

what size unf bolt made from sae grade 5 steel is needed to carry a static tensile load of 3000lb with a safety factor

  A carnot engine operates between temperatures of 700k and

a carnot engine operates between temperatures of 700k and 400k and does 150 j of work in each cycle. what is the

  A submarine is cruising in the ocean at a depth of 320 m

a submarine is cruising in the ocean at a depth of 320 m. salt water has a specific gravity of 1.03. determine the

  What is the reason for the system -to increase the air

what is the reason for the system? -to increase the air pressure from 100 to 1200 kpa design uses dual compressors to

  How do you determine the thickness of a tapering barrel of

how do you determine the thickness of a tapering barrel of a gun at the largest end using pressure temperature on the

  Fig book design of machinerywith using the following data

fig book design of machinerywith using the following data for the above diagram find torque at o2 and forces at o2 a

  The masses will accelerate in a direction that depends on

consider two masses m1 and m2 that are connected by a rope over a pulley. the masses will accelerate in a direction

  What is the maximum mass that can be hung on the end of the

for a 6061 t-6 aluminum beam with dimensions b 3.0 cm d 0.5 cm and length a 30 cm a what is the maximum mass that

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd