Determine a the net power developed in kw b the thermal

Assignment Help Mechanical Engineering
Reference no: EM13644102

Water is the working fluid in a regenerative Rankine cycle. The pressure and temperature at the turbine inlet are 8MPa and 550?C, respectively, and the condenser pressure is 7.5KPa. The mass flow rate of steam entering the turbine is 176kg/s. Included in the cycle is one closed feed water heater using extracted steam at 1800KPa and one open feed water heater operating at 275KPa. Saturated liquid condensate is throttled from the closed feed water heater at 1800KPa to the open feed water heater. The feed water leaves the closed heater at 8MPa, 200?C, and saturated liquid leaves the open heater at 275KPa. The cooling water experiences a temperature increase from 15?C to 27?C with negligible pressure drop as it passes through the condenser. Draw the T-s diagram it would help to begin with a schematic of the cycle) and Determine: a. The net power developed in KW b. The thermal efficiency of the cycle c. The mass flow rate of cooling water in kg/s.

Reference no: EM13644102

Questions Cloud

Knowing that the coefficient of static friction is 040 : a 10 degree wedge is to be forced under end b of the 5 kg rod ab. knowing that the coefficient of static friction is
Knowing that the coefficient of static friction is 020 at : the machine part abc is supported by a frictionless hinge at b and a 10degree wedge at c. knowing that the coefficient
How many liters of hydrogen gas are collected over water : how many liters of hydrogen gas are collected over water at 18 degrees celsius and 725 mmhg when 0.84g of lithium
A cylinder contains a mixture of helium and argon gas in : a cylinder contains a mixture of helium and argon gas in equilibrium at 170degc.a what is the average kinetic energy
Determine a the net power developed in kw b the thermal : water is the working fluid in a regenerative rankine cycle. the pressure and temperature at the turbine inlet are 8mpa
Calculate the heat produced by combustion per liter of : methanol ch3oh is used as a fuel in race cars.a write a balanced equation for the combustion of liquid methanol in
Determine the optimal strategy for the situation by : determine the optimal strategy for the situation by representing it as a game and finding the saddle point. state your
Suppose that in january 2040 you buy a 30-year zero-coupon : suppose that in january 2040 you buy a 30-year zero-coupon u.s. treasury bond with a maturity value of 100000 and a
Starting 2 seconds after the speeder passes the police car : a police car parked by the side of a straight road is passed by a speeding car going at a constant speed of 30 ms.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The vessel is heated until the water pressure reaches 8 mpa

a closed rigid pressure vessel is filled with a saturated mixture of 1.78 kg of liquid water and 0.22 kg of water vapor

  Determine the fatigue strength at 5 x 105 cycles what is

the fatigue data for a brass alloy are given as followsstress amplitude mpa -----------------cycles to failure310

  Machining costs per casting are 600 for the brass-copper

in the design of an automobile radiator an engineer has a choice of using either a brass-copper alloy casting or a

  Nitrogen gas enters an adiabatic nozzle with negligible

1. air is to be compressed from 1 atm and 298 k to 8 atm at a rate of 20000 lmin. a determine if this process should be

  Determine the tension t in the brace as a function of x

the carpenter builds the square frame abcd and then braces it with member ef as shown in order to prevent racking

  A piston has an area of 500 mm2 what mass must the piston

a piston has an area of 500 mm2. what mass must the piston has if it exerts a pressure of 50 kpa above atmospheric

  Two blocks a and b are arranged with pulleys as shown block

two blocks a and b are arranged with pulleys as shown. block a has an initial velocity t 0s to the left of va1.2 ms.

  What is the gauge pressure of the gas in this mercury

what is the gauge pressure of the gas in this mercury manometer if h 81 mm and the atmospheric pressure is 773 mmhg?

  What is the thrust in kn of this engine

Bypass air exits at 600 m/s while combustion air exits at 1000 m/s. What is the thrust in kN of this engine?

  The temperature on the faces of a plane wall

The temperature on the faces of a plane wall 15cm thick are 375 and 85?.The wall is constructed of a special glass with the following properties:k=0.78W/m·?,ρ=2700Kg/m³,Cp=0.84KJ/Kg·?.What is the heat flow through the wall at steady-state cond..

  The aim of this demonstration is to use measurements of the

the aim of this demonstration is to use measurements of the load required to propagate a crack tear in packaging tape

  Obtain the output response signal assuming a first order

a temperature measurement device with a time constant of 0.15 seconds outputs a voltage that is linearly proportional

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd