Determine a the mass flow rate of the refrigerant b the

Assignment Help Mechanical Engineering
Reference no: EM13628992

A heat pump using R-134a as its working fluid is used to keep a space at 25°C by absorbing heat from geothermal water that enters the evaporator at 50°C at a rate of 0.083 kg/s and leaves at 40°C. Refrigerant enters the evaporator at 12°C with a quality of 15 percent and leaves at the same pressure as saturated vapor. If the compressor consumes 1.5 kW of power, determine (a) the mass flow rate of the refrigerant, (b) the rate of heat supply, (c) the COP, and (d) the minimum power input to the compressor for the same rate of heat supply.

Reference no: EM13628992

Questions Cloud

Three balls are randomly chosen without replacement from an : three balls are randomly chosen without replacement from an urn containing 4 red 3 white and 3 blue balls. suppose that
A pure jet engine propels an aircraft at 240 ms through air : a pure jet engine propels an aircraft at 240 ms through air at 45 kpa and -13 c. the inlet diameter of this engine is
The modulus of epoxy is 241 gpa and the modulus of glass : a continuous glass fiberepoxy composite is required to have a longitudinal modulus of 42.0 gpa. the modulus of epoxy is
The pressure in an automobile tire depends on the : the pressure in an automobile tire depends on the temperature of the air in the tire. when the air temperature is 25
Determine a the mass flow rate of the refrigerant b the : a heat pump using r-134a as its working fluid is used to keep a space at 25degc by absorbing heat from geothermal water
The pistons of a v6 automobile develops 225hp if the : the pistons of a v6 automobile develops 225hp. if the engine drive shaft rotational speed is 4700 rpm and the torque is
In a typical sports playoff series two teams play a : in a typical sports playoff series two teams play a sequence of games until one team the eventual winner has won four
Find the transformation matrix r that describes a rotation : find the transformation matrix r that describes a rotation of 90 degrees about an axis from the origin through the
The net potential energy between two adjacent ions en may : the net potential energy between two adjacent ions en may be represented by sum of -ar brn. calculate the bonding

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At the same time measurements showed that the pipe

during drilling of a deep oil well the drill pipe got rigidly stuck. it was necessary to determine the depth at which

  Is the heat transfer one two or three dimensional is there

consider a medium in which the heat conduction equation is given in its simplest form as 1r2 ddrr2dtdr 1a dtdt a. is

  Determine the velocity of the airplane required for pilot

Determine the velocity of the airplane required for pilot to experience weightlessness at the top of the circular path.

  Using navier-stokes equations show that the pressure field

in a chemical coating process a belt is moving with a constant speed of v2 ms. belt is drawing up a liquid film with a

  What are the proper units for your answer to the last

a 2500 kg car traveling at 25.0 ms stops in a distance of 0.300 m after colliding with a tree. what is the acceleration

  Estimate a the percentage chain in toque accompanying a 20

an axial turbine of high hub-tip ratio runs with zero degree reaction and peak efficiency at design flow and speed. the

  Determine the tension t in the cable

System of force and cable tensions is in equilibrium and what are the necessary conditions for static equilibrium and determine the area moment of inertia about Ox for the area shown under the curve

  Determine the maximum allowable tensile load before

a 1 meter section of 1040 steel square tubing is loaded in tesnion. the tubing has an outer edge length of 10mm and a

  Determine the mass flow rate of the air

Determine the mass flow rate of the air passing through this engine and the rates of heat addition and rejection when this engine produces 1000 hp. Assume constant specific heats at room temperature.

  If the member is 1mm thick and the binary diffusion

a thin plastic membrane is used to separate helium from a gas stream. under steady-state conditions the concentration

  A round bar of c14500 copper 15mm in diameter and 250mm

a cylinder made of astm a242 steel is 50cm in diameter and 250mm long and has a wall thickness of 24mm. a round bar of

  The distance between support points is 45 mm 175 in compute

a three-point bending test is performed on a glass specimen having a rectangular cross section of height d 5 mm 0.2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd