Determine a the effectiveness of the regenerator b the rate

Assignment Help Mechanical Engineering
Reference no: EM13643382

A gas refrigeration system using air as the working fluid has a pressure ratio of 5. Air enters the compressor at 0 Celsius. The high-pressure air is cooled to 35 Celsius by rejecting heat to the surroundings. The refrigerant leaves the turbine at ( - 80 C ) and then it absorbs heat from the refrigerated space before entering the regenerator. The mass flow rate of air is 0.4 kg/s. Assuming isentropic efficiencies of 80 percent for the compressor and 85 percent for the turbine and using constant specific heats at room temperature, determine (a) the effectiveness of the regenerator, (b) the rate of heat removal from the refrigerated space, and (c) the COP of the cycle. Also, determine (d) the refrigeration load and the COP if this system operated on the simple gas refrigeration cycle. Use the same compressor inlet temperature as given, the same turbine inlet temperature as calculated, and the same compressor and turbine efficiencies.

Reference no: EM13643382

Questions Cloud

The turbin develops a power output of 1mw at the inlet the : steam enters a turbin operating at steady state with a mass flow rate of 4600kg hr-1 . the turbin develops a power
A high pressure container of methane gas which exhibits an : a high pressure container of methane gas which exhibits an absolute pressure of 200 atms at a temperature of o c. a
The vapour pressure of pyridine is 500 kpa at 3657 k and : the vapour pressure of pyridine is 50.0 kpa at 365.7 k and the normal boiling point is 388.4 k. what is the enthalpy of
A find the force acting on the electron as it revolves in a : in the bohr model of the hydrogen atom an electron moves in a circular path around a proton. the speed of the electron
Determine a the effectiveness of the regenerator b the rate : a gas refrigeration system using air as the working fluid has a pressure ratio of 5. air enters the compressor at 0
The change in gibbs energy that accompanies the oxidation : the change in gibbs energy that accompanies the oxidation of c6h12o6 s to carbon dioxide and water vapor at 250 c is
A person stands on a scale in an elevator as the elevator : a person stands on a scale in an elevator. as the elevator starts the scale has a constant reading of 598 n. as the
A 6300-kg satellite is in a circular earth orbit that has a : a 6300-kg satellite is in a circular earth orbit that has a radius of 3.0 x 107 m. a net external force must act on the
Draw a schematic diagram of the cycle and start with the : an air-standard otto cycle has a compression ratio of 7.5. at the beginning of compression p185 kpa t1320c the mass of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the tension in rope ab

rope AB an AC are thrown to a boater whose canoe has capsized.Given that the angle is 25 and the magnitude of the force FR exerted by the river on the boater is 70N determine the tension in rope AB , in rope AC.

  If the compressor consumes 400 w of power and the cop the

refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at

  Determine the tension in the cable

the frame ACD is supported by a ball-and-socket joint at A and D and by a cable which passes through a ring at B and is attached to hooks at G and H. Knowing that the frame supports at point C a load of magnitude P=268N, determine the tension in t..

  The turbine is not well insulated and thus there is a heat

superheated steam at 500 celsius and 3 mpa enters a steady state turbine with a mass flow rate of 500 kgs. the steam

  The cut-off ratio for the cycle is 2 determine the

an air-standard diesel cycle operates with a compression ratio of 18. at the beginning of the compression process the

  Water is sprayed radially outward over 180 degrees the jet

water is sprayed radially outward over 180 degrees. the jet is in the horizontal plane. if the jet velocity at the

  Hot isostatic pressing hiping should make these products

cast aluminum products often contain gas porosity and shrinkage cavities which can undermine the integrity of these

  A exit p2 - 147 psia v2 2677 ft3lb and u2 10775 btulb

there are supplied to a nozzle 2400 lbhr of steam at an absolute pressure of 200 psia. at the entrance v1 6000 ftmin

  Compute the desities of totally crystalline and totally

the density and associated percent crysallinity for two nylon 66 materials are shown as follows compute the desities of

  Determine a velocity using bernoullis equation

If I take measurements using a Pitot Tube and get results for pressures Horizontal In, Horizontal Out, Vertical In, and Vertical Out all in inches of mercury. How do I take these pressures and determine a Velocity using Bernoullis equation?

  Make a schematic drawing of amorphous si glass with 10 h

if silcion is cooled quickly it will form glass instead of crystallyzingone way to do this is to deposit si atoms onto

  Heat tansfer please find attached some work i need help

please find attached some work i need help with. i have also attached the appendix which the work says is required to

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd