Determine a the air exit velocity to produce 5 lbf b the

Assignment Help Mechanical Engineering
Reference no: EM13639488

An engineering student considers using a fan as a levitation demonstation. She plans to face the box-enclosed fan
so the air blast is directed face down through a 3 ft diameter blade span area. The system weighs 5 lbf, and the student will secure the system from rotating. By increasing the power to the fan, she plans to increase the blade rpm and air exit velocity until the exhaust provides sufficient upward force to cause the box fan to hover in the air. Determine (a) the air exit velocity to produce 5 lbf (b) the volumetric flow rate needed and (c) the minimum mechanical power that must be supplied to the airstream. Take the air density to be .081 lbm/ft^3.

Reference no: EM13639488

Previous Q& A

  After the 300 pipe run this 6 pipe has a sudden enlargement

a 6 nominal pipe size schedule 40 steel pipe has a chamfered entrance and 300 ft. long. the velocity is 20 ft per sec.

  An aircraft landing gear has a probability of 10-5 per

an aircraft landing gear has a probability of 10-5 per landing of being damaged from excessive impact. assuming a

  Calculate the battery failure probability under normal

a particulate monitor has a power supply consisting of two batteries in parallel. either battery is adequate to operate

  The train will be unsafe if the normal acceleration is

a train track is designed with a radius of 20 meters. the train will be unsafe if the normal acceleration is greater

  The buffalo is running at 6 ms at 10 degrees south of east

while riding a horse at 8 ms at 25 degrees to the north of east a rider sees a buffalo he wants to shoot. the buffalo

  We are aware that some states cities and counties have

examine the below topic and provide a hypothesis for which you would use the one-tailed and two-tailed t test to

  A conducting solid sphere of radius 200 cm is located with

a conducting solid sphere of radius 20.0 cm is located with its center at the origin of our three-dimensional

  How much time passes from when the wheel was started from

a sharpening stone at rest is brought to 300 rpm over 2 mins. at that point a dull sword edge is placed against the

  Compute the force of the ground on his feet if he jumps

a boy weighing 3.9 102 n jumps from a height of 1.80 m to the ground below. assume that the force of the ground on his

  Neglecting drag draw a free body diagram and formulate a

a two inch diameter craft ball is thrown vertically. this initial velocity of the ball is 20 fts.a. neglecting drag

Reviews

Write a Review

 

Similar Q& A

  A rankine power cycle operates with an open feedwater

a rankine power cycle operates with an open feedwater heater. the boiler pressure is 6.0 mpa. a superheater provides a

  What is the maximum allowable hole diameter assume y 14

a 4140 steel alloy beam is designed to support a load at 50 of the yield stress. the beam is bolted to a bridge truss

  Under what conditions is the maximum achieved

A steam turbine is operated ith an input temp of 800C and exhaust temp of 150C. What is the maximum amount of work the turbine can do for a given heat input Q? Under what conditions is the maximum achieved?

  A brayton cycle uses air

A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F,

  Assuming there is no friction what will be the final height

a solid cylindrical workpiece made of 5052-o aluminum is 12 cm high and 8 cm in diameter. assuming there is no

  A skydiver jumps from a ballon and falls freely for 6

a skydiver jumps from a ballon and falls freely for 6 seconds. her parachute then opens decelerating her at a constant

  To a man walking with a speed of 2 ms the rain appears to

to a man walking with a speed of 2 ms the rain appears to fall vertically. if the velocity of rain is 4 ms calculate

  Calculate the mass concentration of the aerosol the number

a poly-dispersed aerosol consists of spherical particles within the size range 1.0-10.0 micrometers. the particles are

  Minimize the internal protrusion of the drum

Design the number of teeth and depth of teeth need be chosen. Considerations include the turn angle for each stroke, the bearing stress on the teeth and pins and shear stress on the teeth.

  Use entropy balance for a closed system to determine

use entropy balance for a closed system to determine whether the entropy change of the following processes is positive

  Calculate the work done by the gas when is expands

a sample of argon of mass 10.4 g occupies 2100 ml at 30 degrees.i calculate the work done by the gas when is expands

  Certain system is able to exert an external force f

certain system is able to exert an external force f according to the relationship.v velocityf 15000-500vn for v lt

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd