Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An NC drill press drills four 10.0mm diameter boles at four locations on a flat aluminum plate In a production work cycle. Although the plate is only 12 mm thick, the drill must travel a full 20 mm vertically at each hole location to allow for clearance above the plate and breakthrough of the drill on the underside of the plate. Cutting conditions: speed "" 0.4 m/sec and feed = 0.10 mm/rev. Hole locations are indicated in the following table:
The drill starts out at point (0.0) and returns to the same position after the work cycle is completed. Travel rate of the table in moving from one coordinate position to another is 500 mm/min. Owing to effects of acceleration and deceleration and the time required for the control system to achieve final positioning, a time loss of 3 seize patience at each stopping position of the table, Assume that al1ll1ove~are made to minimize the total cycle time If loading and unloading the plate take 20 sec (total handling time. determent the time required for the work cycle.
A large brass washer has a 2-cm inside diameter, a 5-cm outside diameter, and is 0.5 cm thick. Its conductivity is s = 1.5 × 107 S/m. The washer is cut in half along a diameter, and a voltage is applied between the two rectangular faces of one par..
A 200 nm oxide film is deposited on a 500 m thick bare silicon wafer that has a radius of curvature of 300 m. After deposition, the radius is measured to be 200 m. A 600 nm nitride film is now deposited on the oxide
Determine the energy uses on farms in middle east and determine whether or not it is better to use a stand alone system or a grid connected system for the application on farms.
The time taken to download software from the internet is uniformly distributed between four and ten minutes. A. What is the probability that the downloading time for software is more than six minutes B. Prob that time is between five and eight minute..
Design four by four combinational binary multiplier using hierarchical design method, use switches as inputs, use LEDs as outputs, download design on FPGA and show your demo. You must design this part in VHDL.
A three-phase, four-wire system operating with a 208-V line voltage is shown in Fig. 12.64. The source voltages are balanced. The power absorbed by the resistive wye-connected load is measured by the three-wattmeter method.
An inverting amplifier must provide an input impedance of approximately 10 k Ω and a nominal gain of 4. If the op amp exhibits an open-loop gain of 1000 and an output impedance of 1 k Ω, determine the gain error.
The length of a wire of a potentiometer is 100 cm, and the e.m.f. of its stand and cell is E volt. It is employed to measure the e.m.f. of a battery whose internal resistance is 0.5 ohm. If the balance point is obtained at l =3..
1. for the waveform shown below obtain expressions for fourier components for fundamental 5th 7th and 11th elements
In which case does the output suffer distortion? What influenced your answer?
An engineering firm consisting of 3 programmers and 6 circuit engineers. The employees are randomly assign to 3 teams of 3, labeled Group 1, Group 2, and Group 3. a) How many ways are there to assign the 9 employees to Groups 1, 2 & 3
Sketch the local resistance of the channel (per unit length) as a function of x.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd