Designing a motor shaft for brushless motor

Assignment Help Mechanical Engineering
Reference no: EM131538355

Given a brushless motor that should redesign a motor shaft for it because the current size of the OD motor shaft is smaller than it should be.

The professor said, there is a cam installed in the shaft, but there is a problem with thickness wall of the OD surrounding the Thread of the cam

  • We need to come with standard (t) that fit the diameter of the cam and the OD.
  • Look at the below picture (figure one)
  • Designing a motor shaft for brushless motor:
  • Specify the bearing standard. in the front and the back
  • The length of ( Lm ) is not changing ; Look at the below picture
  • The cam diameter is not changing
  • Specify the thickness wall of the thread where the cam is inserted in.
  • The parameter of the motor is not changing.
  • Provide the tolerance of the thread and the bearing standard
  • Show all work in steps (Hand writing) with all formula used to dot eh calculation
  • Please, do not use tables to make the calculation

Information (attached), you might need to do the calculation.

Attachment:- Assignment File.rar

Reference no: EM131538355

Questions Cloud

What is difference in the annual inflation rates : What is the difference in the annual inflation rates for the United States and Russia over this period?
How valid is an estimate of the cost of debt : How valid is an estimate of the cost of debt based on 15-year bonds? If the estimate is not valid, how might it be adjusted to remove any bias?
The piece of equipment used to manufacture roof tiles : What is Jeffrey’s MACRS deduction for the piece of equipment used to manufacture roof tiles in 2012?
Biomedical products positioning importance topics : Writing Assignment Title: Biomedical Products Positioning Importance Topics to be addressed:
Designing a motor shaft for brushless motor : Given a brushless motor that should redesign a motor shaft for it because the current size of the OD motor shaft is smaller than it should be
Forecast for this pair exchange rate : What is the 1 month and the 6 month forecast for this pair’s exchange rate? Which currency is becoming stronger and by what %?
What evidence would you look for on film and in the ring : All on film. MMA fight. One fighter dies from a single punch to the chest. Is it possible to determine cause of death?
Find a house with a gunshot victim : You find a house with a gunshot victim. Gun in living room next to the body. Cell phone next to the body. Suicide note on living room table.
Explaining the concept of chronic inflammation : Write a short paragraph explaining the concept of chronic inflammation as an altered inflammatory response. Use the Internet as a resource.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd