User Account

All Pages

Design the signal conditioning

Assignment Help Electrical Engineering
Reference no: EM131392673

A sensor linearly changes resistance from 2.35 to 3.57 kΩ over a range of some measured variable.

The measurement must have a resolution of at least 1.25 kΩ and be interfaced to a computer. Design the signal conditioning and specify the characteristics of the required ADC.

Reference no: EM131392673

Questions Cloud

Develop a block diagram of the required signal : Develop a block diagram of the required signal conditioning so that each of these can be connected to the DAS and so that the indicated variable range corresponds to 00H to FFH.
What is minimum time between samples for particular channel : The multiplexer can select and settle on a channel in 3.1µs, the ADC converts in 33 µs, and the computer processes a single channel of data in. What is the minimum time between samples for a particular channel?
Develop a list of best practices being used by businesses : Develop a list of best practices being used by businesses in chosen industry to address the identified regulatory issues. How these best practices could be applied to solve a specific problem for another student's employer.
Develop the signal conditioning and adc reference : The flow is measured as a voltage given by V = 0.0022 Q2, where Q is the flow in. Develop the signal conditioning and ADC reference that will provide this specification.
Design the signal conditioning : The measurement must have a resolution of at least 1.25 kΩ and be interfaced to a computer. Design the signal conditioning and specify the characteristics of the required ADC.
Prepare a flowchart of software : Prepare a flowchart of software that inputs data from channel 2 and then channel 6.- Develop an equation that relates the analog output voltage to the two analog input voltages.
What is the minimum sampling rate to ensure quality data : A computer will be used to control flow through 10 pumping stations. The pumps exhibit a surging effect with a period of 2.2 s. What is the minimum sampling rate to ensure quality data?
Devise a flowchart and program : Devise a flowchart and/or program in the language of your choice that makes the reference correction and performs linearization by table lookup and interpolation. Use table values in increments for a type-K TC with a reference.
What is the percent error in the model moment of inertia : Combine the data from problems 13-7 and 13-9. Run the linkage at a constant 2000 rpm. Calculate the inertia force and inertia torque at rot= 45°. Piston mass= 0.012.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Compare gasoline with the energy content per unit mass

A typical lead acid storage battery has a mass of 30 kg. Starting from a fully charged state, it can supply 5 A for 24 hours with a terminal voltage of 12 V before it is discharged.

  What is fraction of the chip occupied

What is fraction of the chip occupied by other areas, such as I/O connections, peripheral circuits, and interconnect?

  Determine the magnitude p of the forces

The C-shaped steel bar is used as a dynamometer to determine the magnitude P of the forces shown. Knowing that the cross section of the bar is a square of side 40 mm and that the strain on the inner edge was measured and found to be 450 µ, determi..

  Plc design using mitsubishi programmable logic controller

PLC design using mitsubishi programmable logic controller (model GX ICE simulator) - Summarise your work with a brief report with approximately 5 pages of write-up

  What is the range of the sensor voltage outputs

A manufacturer specification sheet lists the transfer function of a pressure sensor as 45±5% mV/kPa with a time constant of 4±10%. A highly accurate test system applies a step change of pressure from 20 kPa to 100 kPa.

  Determine the time constants of the combined thermocouple

Determine the time constants of the combined thermocouple-thermal-well system Assume that the weight of the thermocouple is 8 g and the weight of the thermal well is 40g. Assume also that the specific heats of the thermocouple and thermal well are..

  Which is the correct syntax for the concurrent signal

The detector will take in numbers from 1510 to 010 encoded in binary labeled [N3:N0] with N3 being the most significant bit. The output will be asserted when the decimal value of the input is a prime number (i.e., 2,3,5,7,11,13). The output is de-..

  Copper heater of thermal conductivity

For the foregoing heat rate and a copper heater of thermal conductivity k h = 400 W/m · K, what is the required volumetric heat generation within the heater and its corresponding centerline temperature?

  Determine the final temperature of nitrogen

A piston-cylinder device initially contains 1 m of nitrogen gas at 400kpa and 27 c. A resistance heater is turned on inside the cylinder which passes 70 kj of electricity to the nitrogen gas.

  Explain what will the new mean and variance

Maximum Likelihood to get the above parameters i.e. u0 and var. Now from these 999 points, I take one point out (lets call it i) and add a new point (lets call it j). What will the new mean and variance be?

  How is the available energy from uranium fuel determined

How is the available energy from uranium fuel determined?

  Which ic or ics are not working correctly

There is a malfunction in a digital system that contains several multiplexer and demultiplexer ICs. A reading was taken at each pin with a logic probe, and the results were recorded in Table 8-7. Which IC or ICs are not working correctly?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd