Design the low pass filter with the 3 db point

Assignment Help Electrical Engineering
Reference no: EM13277443

Design the low pass filter with the 3 dB point at 1Khz. DC gain is 0 dB. use the C value as 100 uf and input ac magnitude 1 V. use the AC simulation between 1 mHz to 1 Khz.

Reference no: EM13277443

Questions Cloud

How to estimate the mass of nitrogen in the tank : The pressure gauge on a 20.0 m3 tank of nitrogen at 25 C reads 10 bar. Estimate the mass of nitrogen in the tank by : (a) Direct solution of the ideal gas equation of state. (b) Conversion from standard conditions.
What problems could switch bounce cause in applications : A "Clock" pulse for a flip-flop could be generated by manually filpping a switch from 0 to 1 and then back to 0. but switches such as those on the logic designer "bounce" when switched from on state to another.
Compute the average force that the racket exerts on the ball : A tennis player swings her 1000 g racket with a speed of 15.0m/s . She hits a 60 g tennis ball that was approaching her at a speed of 15.0m/s. compute the average force that the racket exerts on the ball
Againfind daily load factor and the required energy ratio : The daily load factor of a given entity is defined as the total daily energy served to that entity divided by theproduct (peak demand)*(duration of the time interval). For a daily load factor, the duration of the time interval is 24.
Design the low pass filter with the 3 db point : Design the low pass filter with the 3 dB point at 1Khz. DC gain is 0 dB. use the C value as 100 uf and input ac magnitude 1 V. use the AC simulation between 1 mHz to 1 Khz.
Explain the concentration of the first ion to precipitate : Sodium phosphate is added to a solution that contains 0.0014 M aluminum nitrate and 0.078 M calcium chloride. The concentration of the first ion to precipitate (either Al3+ or Ca2+) decreases as its precipitate forms
Calculate the speed of the resulting ball of clay : A 40.0g ball of clay traveling east at 3.00m/s collides, What is the speed of the resulting ball of clay
Derive the expression for equilibrium concentration of holes : Derive the expression for the equilibrium concentration of holes/cm^3 in the valence band, p0, starting with the density of states in the valence band and the Fermi-Dirac distribution.
Compute the solubility of copper iodate : Calculate the solubility of copper (II) iodate in 0.56 M copper (II) nitrate. Ksp* is 7.4x10-8 M3.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate back emf of the motor

A six pole, 400 V d.c. motor draws 110 A from the supply. The shunt field resistance is 200 Ohm and the armature resistance is 0.5 Ohm. The armature is wave wound with 600 conductors operates at a speed of 1200 rev/min when supplying full load.

  Design a combinational circuit with four inputs

Design a combinational circuit with four inputs, x,y,w, and z, and four outputs: A, B, C, and D. When the binary input value in decimal is 3,8,12 or 15, the binary output value is one less than the input value, otherwise it is one greater than the..

  Determine the magnitude of the acceleration of the car

A jogger accelerates from rest to 3.75 m/s in 3.58 s. A car accelerates from 16.7 to 31.6 m/s also in 3.58 s. (a) Find the magnitude of the acceleration of the jogger. (b) Determine the magnitude of the acceleration of the car.

  How many atoms are there in the unit cell of si lattice

(b) Verify that there are 4.994×(10 to the power 22) atoms per cubic centimeter in the Si lattice at room temperature. (c) Determine the center to center distance between nearest neighbours in the Si lattice.

  Sketch the unit step response of the system

Sketch the unit step response of the system below. Show the magnitude of the steady state on the c(t) axis of your response curve and the value of the time constant on the t axis. T(s)=C(s)/R(s)=5/s+2.5

  How far does sam land from the base of the cliff

Sam (75 ) takes off up a 50--high, 10 frictionless slope on his jet-powered skis. The skis have a thrust of 200 . He keeps his skis tilted at 10 after becoming airborne. How far does Sam land from the base of the cliff

  How big will be torque on shaft of motor is efficiency

mutual shifted by 90 degree currents through each of both windings of the single phase A motor are (5.5+1.7) A but RMS voltage of the supply is 220 V. How big will be torque on shaft of the motor is efficiency factor (\eta\) is 0.7

  Draw ac equivalent ckt with load impedance element equated

A three phase 4.157kv 60hz power system serves a 2880kva load pf=.8 lagging. Draw the ac equivalent circuit with load impedance element equated. The load is delta connected. solve for all the current (6 total).

  Calculate the friction and windage-rotational losses

A six pole, 40 kW, 400 V d.c. motor draws 110 A from the supply. The shunt field resistance is 200 Ohm and the armature resistance is 0.5 Ohm. The armature is wave wound with 600 conductors operates at a speed of 1200 rev/min when supplying full l..

  How is the effect of frequency-selective fading

How is the effect of frequency-selective fading on basic OFDM signaling and what techniques can one use in OFDM to overcome fading?

  Find the exit velocity and the 2nd law efficiency

Steam enters an adiabatic nozzle at 3.5Mpa and 300C with a low velocity and leaves at 1.6Mpa and 250C at a rate of 0.4kg/s. If the surrounding is 10 at 100Kpa and 18C, find A) The exit velocity B)The 2Nd law efficiency

  Design circuit that can charge your capacitor safely at 25v

You chanrge your capacitor above by connecting them to a non-ideal 30-Volt source with a Thevanin resistance of 5 ohm. Since you are careful not to go above the capacitor 25-V rating, design a circuit that can charge your capacitor safely at 25V

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd