### Design the entire circuit implementing each of the output

Assignment Help Electrical Engineering
##### Reference no: EM13278854

Design a combinational circuit that forms the 2-bit binary sum S1S0 of two 2-bit numbers A1A0 and B1B0 and has both a carry input C0 and carry output C2. Design the entire circuit implementing each of the three outputs with a two-level circuit plus inverters for the input variables. Begin the design with the following equations for each of the two bits of the adder:

S(i) = Ai'Bi'Ci + Ai'BiCi' + AiBi'Ci' + AiBiCi
C(i+1) = AiBi + AiCi + BiCi

### Write a Review

#### Define a three-phase overhead transmission line

A three-phase overhead transmission line has a per-phase resistance of 0.15 ohm/km, and a per-phase inductance of 1.3263 mH/km.

#### How do graphical representations relate to the phase angles

When making an impedance diagram, does inductive reactance go on the positive Y-axis, or the negative Y-axis. How about capacitive reactance. How do these graphical representations relate to the phase angels of the reactances.

#### Determine the amount of gas in the container

Nitrogen at an absolute pressure of 689.5 kPa is used to fill a container having a volume of 0.002 m3. The filling process is very slow, and the gas in the container attains the ambient (room) temperature of 20°C. Determine the amount of gas in th..

#### Determine stability by using the state space solution

Convert the following differential equation 5 (t) +4 (t) +3x.(t) + 2x(t) + 7u(t) - 5u.(t) + 2 (t) = 0 to state space form. Is this system marginally stable, asymptotically stable, or unstable when u(t) = 0 Determine stability by using the state sp..

#### Determine values of t for which signal is guaranteed to be 0

Let x(t) be a signal with x(t)=0 for t

#### Design a moore sequential machine that has one input x

Design a Moore sequential machine that has one input X and one output Y. Whenever X changes from 0 to 1, Y should become 1 for two clock cycles and then return to 0 - even if X is still 1. For example, given an input sequence X=0110101001.

#### What is new phase shift at freq where feedback gain is one

Assume that at this point when Av*β = 1, phase shift due to the amplifier is 120 degrees. A 0.001 micro farad capacitor is added in parallel with Rf in the feedback circuit. What is the new phase shift at the frequency where Av*β = 1

#### Calculate the line-lo-line voltage at sending end of feeder

The transformer is supplying a load of 325 MVA, with 0.93 power factor lagging at a voltage of 24 kV (line-to-line) on its low-voltage side. It is supplied from a feeder whose impedance is 0.11 + j2.2 ohms connected

#### Write a program that reads a nonnegative integer

The factorial of a nonnegative integer n is written n! (pronounced "n factorial") and is defined as follows: n!= n(n-1)(n-2)(n-3)....1 (for values of n greater than or equal to 1) and n!= 1 (for n=0) for example 5! = 5x4x3x2x1,

#### Find the expression for the group delay of the system

Consider a continuous-time LTI system with frequency response of H(j omega) = 1 + j 250 omega/(2 - j 50 omega)2 Find the expression for the magnitude of H(j omega) and sketch its Bode plot (sketch asymptotes and the magnitude curves).

#### Calculate the transformation matrix used to rotate an image

(a) Calculate the transformation matrix used to rotate an image by 45o clockwise about the Zaxis. (b) How would you use this transformation matrix to achieve the desired rotation (c) Use the transformation matrix to rotate the image point (x,y) = (0,..

#### Describe what type of damping is exhibited by v

the voltage v in a certain circuit is described by the differential equation 3v"+24v'+75V=0 a) determine the values of α and w0 b) what type of damping is exhibited by V(t)