Design the condenser of a steam power plant that has a

Assignment Help Mechanical Engineering
Reference no: EM13641333

Design the condenser of a steam power plant that has a thermal efficiency of 40 percent and generates 10 MW of net electric power. Steam enters the condenser as saturated vapour at 10kPa, and it is to be condensed outside horizontal tubes through which cooling water from a nearby river flows. The temperature rise of the cooling water is limited 8 degC, and the velocity of the cooling water in the pipes is limited to 6 m/s to keep the pressure drop at an acceptable level. From prior experience, the average heat flux based on the outer surface of the tubes can be taken to be 12,000 W/m^2. Specify the pipe diameter, total pipe length and the arrangement of the pipes to minimize the condenser volume.

Reference no: EM13641333

Questions Cloud

Identify the independent and dependent variables classify : for a research project in a political science course a student has collected information about the quality of life and
Assume no slipping of the cylinder and determine the : a cord is wound in the slot of cylinder a. mass b moves downward with a velocity of 6 m. assume no slipping of the
In testing a relative stabilities of cu ii species using a : in testing a relative stabilities of cu ii species using a well plate a student adds 6 drops of 1 m of nh3 to 6 drops
The atomic mass of gold is 197 gmole and the density of : you hang a heavy ball with a mass of 12 kg from a gold wire 2.6 m long that is 2 mm in diameter. you measure the
Design the condenser of a steam power plant that has a : design the condenser of a steam power plant that has a thermal efficiency of 40 percent and generates 10 mw of net
A 27 pound meteorite struck a car leaving a dent 25 cm deep : a 27 pound meteorite struck a car leaving a dent 25 cm deep in the trunk. if the meteorite struck the car with a speed
Each person picks 12 mampm chocolates from the bag what is : students of dr. psychicu2019s training class wanted to see if they do learn the skills at the end of the class. each
Find considering only loss of heat from water heater what : given 55 galloin water heater height 61 in. dia 21.5 in. surrounding insulation k0.03 btuft-hr deg. f tank is in
Determine the boiling point elevation of a solution of : determine the boiling point elevation of a solution of 133.0 mg of carvone c10h14 oil of spearmint dissolved in 1.500 g

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd