Design parameters for the containment vessels are as

Assignment Help Mechanical Engineering
Reference no: EM13621404

Select a steel for use in high-pressure cylindrical containment vessels for the next generation of nuclear submarines. Two steels are being considered for this application, HY-130 and HY-180, which are both martensitic steels. The material properties for these two steels are shown in the table below.

PROPERTIES HY-130 HY-180

Yield strength, ksi. 130 180

Tensile strength, ksi 150 190

K~c, ksiX/~n. 280 300

K~c in seawater, ksiX/~n. 260 180

Hypothetical cost $/lb 0.50 1.00

Design parameters for the containment vessels are as follows:

(a) Internal pressure = 5000 psi

(b) Internal diameter of cylindrical portion -- 30 in.

(c) Overall length of each vessel is 20 ft. Ends are to be hemispherical.

(d) Welded fabrication will be used. Assume that weld metal properties are the same as base metal properties.

(e) The vessel must have a factor of safety of at least 2.0 against both yielding and fracture of a 0.5-in-deep surface flaw. Assume that a/2c is 0.4.

(f) The vessels will be cycled from 0 to full design pressure (5000 psi).

(g) Inspection is such that all flaws greater than 0.05 in. can be found during fabrication. In service, the vessels will be in the forward-flooding zone of the submarine and cannot be Inspected, although they can be protected by painting.

Reference no: EM13621404

Questions Cloud

The capped orifice on the side has a 4-cm diameter exit : the open water tank is resting on a frictionless plane. the capped orifice on the side has a 4-cm diameter exit pipe
Test claim use hypothesis test claim by constructing an : in a recent nyc marathon 25221 men finished and 253 dropped out. 12 883 women finished and 163 dropped out use a 0.01
If the velocity out the 2-cm-diameter tube is 15 ms : water flows into a volume that contains a sponge with a flow rate of 0.02 m3s. it exits the volume through two tubes
Des the mean weight for the generic soda appears to be : use the weights of cans of generic soda as sample one and use weights of cans as the diet version of that soda as
Design parameters for the containment vessels are as : select a steel for use in high-pressure cylindrical containment vessels for the next generation of nuclear submarines.
A simple random sample of 50 adults is obtained and each : a simple random sample of 50 adults is obtained and each persons red blood cell count is measured. the sample mean is
The data shows the list and selling prices for homes find : the data shows the list and selling prices for homes. find regression equation letting the list price be independent x
In studying the occurence of genetic characteristics the : in studying the occurence of genetic characteristics the following sample data were obtained. at the 0.05 significance
The heights of 18-year-old men are normally distributed : the heights of 18-year-old men are normally distributed with a mean of 68 inches and a standard deviation of 3 inches.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd