Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A tank of fluid employed in a chemical process is being monitoredwith three sensors. The sensors measure temperature, pressure andfluid level. If all the sensor measurements are in the normalrange, the sensor outputs are low. If the measurements are outsidethe normal range, the sensor outputs are high. Design a logiccircuit that will produce a high signal for an alarm under the following conditions:
1. pressure and temperature are too high.2. fluid level is too high and either pressure or temperature or both are too high.
A parallel circuit consists of a source and three resistors in parallel (R1=100-ohm; R2=200-ohm, and R3=300). The resistor of 100? draws a current of 500mA. a) Find the voltage across R1 b) Derive the current through R2 and R3
Assume, the program is to start at $C000. The program is to sort a block of 8-bit data where the starting address of the data block is stored at location $8000/8001 and the 8-bit data where the starting address of the data block is stored at $8002..
Teh energy stored in a 2H inductor os 130 J and is increasing at 200 J/s at t=4s. A) Determine the current magnitude at t=4s. B) Determine the voltage magnitude at t=4s.
Determine whether the following signals are periodic. If they are, find the smallest periods (fundamental periods). a) f(x,y) = sin (2 pi x) cos(4 pi y) b) Discrete signal: f(m,n) = sin ( pi * m / 5) cos(pi * n / 5)
A terrestrial radio link transmits a CDMA signal from a base station using a spreading code with a chip rate of 1.0 Mchips per seconds. The message data rate of the signal is 10 kbps.
(a) Find Cox and (b) For an NMOS transistor with W/L = 15 m/0.25 m, calculate the values of VOV , VGS, and VDSmin needed to operate the transistor in the saturation region with a dc current ID= 0.8mA.
Use Matlab to verify the above results and determine: a. The starting torque b. The maximum torque c. The slip at which the motor develops maximum torque d. Draw the torque-speed characteristic of the motor
Compute y(nT) iteratively for n=0, 1, 2, when, y(-T)=2, and x(nT) = u(n) Hint: the initial conditions are given for negative n. Shift the equation to the right to express x() and y() to eliminate all advances and end up with x(n), y(n)
For the amplifier in Fig. P4.20, the maximum value of VS is 2 V and the op-amp can deliver no more than 100 mA. (a) If +-10 V supplies are used, what is the maximum allowable value of R2 (b) Repeat for +-3 V supplies.
Consider an ideal 12-bit ADC with Vref=5V is used to sample a1v p-p sinusoidal signal that has a 2.5v offset. What is the boolean output if the input voltage is 3.333v
What is the inverse Laplace transform of 32/s(s^2+64). Please show all work.
In addition, the stopbandattenuation is to be at least 65 dB, starting at the Nyquistfrequency of 22.05 kHz. The complexity of the filter shouldbe minimized. Sketch the filter specification (amplitude vs.frequency). Which filter family would you e..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd