Design heating system for a public pool located in the city

Assignment Help Mechanical Engineering
Reference no: EM131498617

Question: The City of Edmonton has solicited the services of a mechanical engineering consulting firm to design a heating system for a public pool located in the City. The pool will be 20 ft wide and 15 ft long. It will be 4 ft deep at one end, varying linearly along the length of the pool to a depth of 10 ft. The pool water is to be heated to 77?F in the month of May. The focus of the design will be to provide a system that can heat the water from an initial temperature, after winter closure.

The 2006 Alberta Building Code, Division B, Section 7.3.3.9 requires that the slope of the bottom of public swimming pools be no more than 1:3. Section 7.3.3.39 of the same code also requires that the turnover period (recirculation period) of the pool water shall not exceed 4 hours. Design a heating system that is complete with one or more boiler packages. The maximum length of the piping system may be 25-50 ft from the pool. Reference to the 2006 Alberta Building Code may be useful.

Reference no: EM131498617

Questions Cloud

About its profitability index and discounted payback : Suppose a project has conventional cash flows. About its discounted payback? About its profitability index?
Prepare an equipment schedule for client contract documents : A low-velocity residential air duct is to be equipped with a manufacturer's heating module. It is expected that the module will temper dry air by heating.
Satisfaction for a simpler website : Is it necessary to do full life cycles for simpler websites or not. Even if we do: How can we measure user satisfaction for a simpler website?
What is koses weighted average cost of capital : Kose has a beta of 1.3. The market portfolio’s expected rate of return is 14%, and the risk-free rate is 6%. What is Kose’s weighted average cost of capital?
Design heating system for a public pool located in the city : The City of Edmonton has solicited the services of a mechanical engineering consulting firm to design a heating system for a public pool located in the City.
Describe the role of each of the players you identified : Explain who all the players are - official and unofficial, and interest groups - involved. Describe the role and function of each of the players you identified.
Continuously compounded zero-coupon bond yields : Suppose you observe the following continuously compounded zero-coupon bond yields
Which system is better for managing global affairs : Which system is better for managing global affairs, collective security or the balance of power?
Determine the minimum amount of fuel : A tank less water heater is required to heat water to 140?F for domestic use. The water flow rate should be fixed between 2 and 4 gpm.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd