Design circuit for light fixture controlled by four switches

Assignment Help Electrical Engineering
Reference no: EM13294190

design a circuit for a light fixture controlled by four switches,where flipping one of the switches turns the light on when it isoff and off when it is on. give expression and show using logic gates.

Reference no: EM13294190

Questions Cloud

Explain the dry basis concentration of carbon dioxide : What is the dry basis concentration of carbon dioxide using the concentration data given below. Conc. CO2 (Wet) = 15.4% and Conc. H2O = 4.3%
What is her new angular velocity : An ice skater is rotating at 3.4rev/seconds while her arms are beside her. The moment of inertia of the skater is 5kg x m^2. what is her new angular velocity
How art movements typlified german expressionism : what how art movements typlified german expressionism? Les Demosiselles D; Avignon was the breakthroughough work of what artist ? by 1910 kandinskys work made a total shift to what form of art ? who worked with picasso in the persuit of cubism ?
Determine the water velocity at the restriction : Water having a density of 1000kg/m^3 is flowing with a velocity of 3 m/s through a pipe. Determine the water velocity at the restriction
Design circuit for light fixture controlled by four switches : design a circuit for a light fixture controlled by four switches,where flipping one of the switches turns the light on when it isoff and off when it is on. give expression and show using logic gates.
Solve the system for second order runge-kutta : Determine the angle of the pendulum as a function of time for the first 18 seconds after release and solve the system for second order Runge-Kutta
How to calculate the ph of the solution perchloric acid : A chemist dissolves 253 mg of pure perchloric acid in enough water to make up 330 ml of solution. Calculate the pH of the solution.
Find the amount of interest earned in the fifth year : Assume that delta t = 1/[10(1 + t)^2] and A(0) = 100. Find the amount of interest earned in the fifth year.
Design a one input one output serial 2s complement : design a one input one output serial 2's complement. the circuit accepts a string of bitsfrom the input and generates the 2's complement at the output thecircuit can reset asnchronously to start and end the operation

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the force opposing the motion of the bus

The electric motor in a street car develops a power output of80 hp at 1200 rpm as the vehicle moves up a hill at a speed of 30mph. Assume the gearing losses are negligible, calculate: (a) The torque developed by the motor.

  How the two identical cs amplifiers are connected is cascade

Two identical CS amplifiers are connected is cascade. First stage is fed with a source Vsig having a resistance Rsig = 100k Ohm. A load resistance Rl = 10k Ohm is connected to the drain of the second stage.

  What value of current limiting resistor is required

An LED is connected to a 74LS244 in an active-LOW configuration. The key parameters for the 74Ls244 are IOH=-15 mA, IOL=20 mA, VOH =2.0V and Vol=0.5V. The LED has a voltage drop of 2.0V and an operating current of 15 mA.

  What is the reliability and the equivalent mtbf value

What is the reliability, the equivalent MTBF value, and the equivalent failure rate for a system that has a primary microprocessor circuit board and a secondary microprocessor circuit board that is hooked up in standby redundancy

  Sketch the trellis diagram and ?nd the output bit sequence

Consider the convolutional code described by connection polynomials

  How much work is done in moving avogadros number of electron

how much work is done(by a battery,generator,or some other source of potenial difference) in moving Avogadro's number of electrons from an initial point where the electric potenial is 9.00V to a point where the electric potenial is -5.00V

  Design a c-filter so that the ripple factor of the output

A single - phase bridge rectifier is supplied from a 120 - V, 60 - Hz source. The load resistance is R = 200 ohm. a ) Design a C - filter so that the ripple factor of the output voltage is less than 5%.

  Find the midband gain and the upper half-power freq

The available powersupply voltages are VCC = 15 V andVEE=-15 V. Maximize |Avs| in a manner consistent with the otherspecifications. Use SPICE to find the midband gain and the upperhalf-power frequency for your design.

  Find when the triggering angle is greater than 140 degrees

The average voltage across the load when the triggering angle is 140 degrees. Keep in mind that the conduction is incomplete when the triggering angle is greater than 140 degrees.

  Write a program to genrate a square wave

assuming XTAL=11.0592 MHz,write a program to genrate a square wave of 20 Hz frequency on pin2.3?

  How much gain in decibels will be required of the amplifier

a sound distribution system has the following outputs 10 watts at 8ohms,5watts at 4 ohms, 15 watts at 16 ohms and 2 watts at 4 ohms if the input to the amplifier is 20 millivolts at 600 ohms how much gain in decibels will be required of the amplif..

  Determine the frequency response and the magnitude response

determine the frequency response and the magnitude response of the z tranfer function below. please show step to step how to get the result. D is a positive interger

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd