Design base isolation system for electronic module of mass

Assignment Help Mechanical Engineering
Reference no: EM131143969

Design a base isolation system for an electronic module of mass 5 kg so that only 10% of the displacement of the base is transmitted into displacement of the module at 50 Hz.

What will the transmissibility be if the frequency of the base motion changes to 100 Hz? What if it reduces to 25 Hz?

Reference no: EM131143969

Questions Cloud

Calculate the stiffness required of the isolation pads : Calculate the stiffness required of the isolation pads to accomplish this design goal - It is desired to reduce the amplitude of the transmitted force by 80% using isolation pads.
Determine the largest offset that can be used : Knowing that the maximum stress after the offset is introduced must not exceed 4 times the stress in the tube when it is straight, determine the largest offset that can be used.
Find percent of motion transmitted to the instrument panel : Find the percent of motion transmitted to the instrument panel if it weighs 50 lb.
What is the most influential factor in lifting : What is the most influential factor (i.e. multiplier) in lifting? The management style where the boss spends more time "on the floor" than in his/her office is called
Design base isolation system for electronic module of mass : What will the transmissibility be if the frequency of the base motion changes to 100 Hz? What if it reduces to 25 Hz?
What is the wavelength of the standing wave pattern : The speed of waves along the string increases with increasing tension in the string. Should the magnitude of M be increased or decreased in order to double the number of antinodes in the standing wave pattern. Justify your answer.
Calculate the damping ratio required : Calculate the damping ratio required to limit the displacement transmissibility to 4 at resonance for any damped isolation system.
Determine the radius of curvature r : A W200 X 31.3 rolled-steel beam is subjected to a couple M of moment 45 kN.m. Knowing that E = 200 GPa and n = 0.29, determine
Determine the largest couple m that can be applied to a beam : (a) Using an allowable stress of 120 MPa, determine the largest couple M that can be applied to a beam of the cross section shown. (b) Solve part a, assuming that the cross section of the beam is an 80-mm square

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd