Design an open-ended shunt stub matching network

Assignment Help Electrical Engineering
Reference no: EM13254208

A half-wave dipole antenna has an input impedance Zant = 73.2 + j42.5 ohms. Design an open-ended shunt stub matching network to match this antenna to a 50ohm line.

Reference no: EM13254208

Questions Cloud

Discuss the common logistics measures in transportation : Discuss the common logistics measures in transportation, warehousing, and inventory management.
Calculate the wavelength of light emitted : suppose that hydrogen atoms are prepared in the n=2 energy level. calculate the wavelength of light emitted by these excited atoms when returning to the ground state.
Find the time it takes the population of this town to double : The population of a community was 12500 in 1985 and 36000 in 2000.  Find the time it takes the population of this town to double
What is the overview of specifications of the law : Pertaining to Affirmative Action. What is the overview of specifications of the law, including the criteria for a discrimination claim to be successful.
Design an open-ended shunt stub matching network : A half-wave dipole antenna has an input impedance Zant = 73.2 + j42.5 ohms. Design an open-ended shunt stub matching network to match this antenna to a 50ohm line.
Independent contractors and labor force : Which of the following statements best explains the term labor force. Which of the following skills are more actively sought by U.S. employers today? Independent contractors are:
Internationalisation of regulations : Identify three areas to support the above statement and discuss how these areas would benefit a country in trade and commerce.
State the iupac substitutive name of the alkene : Write the IUPAC substitutive name of the alkene that will produce 2-bromohexane relatively free of isomers by the Markovnikov addition of HBr.
What happens to current across the capacitor after long time : A circuit that is made from a voltage source in series with the switch then in series with the parallel set of a resistor and a capacitor. The switch is originally open, it is then closed.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the line impedance of thje souece

In a balanced three-phase wye-wye system, the load impedance is 4 + j3 . The source has phase sequence abc and Van = 120

  Determine the power to which the motor can be loaded slowly

A 3-phase, 2300 V, 60 Hz, 12-pole, Y-connected synchronous motor has 4.5 ? per phase synchronous reactance and negligible stator winding resistance. The motor is connected to an infinite bus and draws 250 A at 0.8 power factor lagging.

  What would be the channel snr for the new system

Binary data is transmitted at the rate of Rb bits/sec over a channel occupying a bandwidth B and the channel SNR=3 dB. If the data bit rate is increased to 2.65Rb and the bandwidth is increased to 1.75B i.

  Determine what is the terminating load impedance

Use Smith Chart: A 100 Ohm air-coaxial transmission line is measured to have an input impedance of 100 + j100 Ohms. If the system is operated at 100 MHz and is one meter long, what is the terminating load impedance

  Determine the peak-to-peak current ripple in the output

1. Determine the peak-to-peak current ripple in the output inductor for a forward converter and determine the output voltage ripple of the converter. We know the following parameters: duty cycle d, input voltage Vin, turn ratio.

  Evaluate the discrete fourier transform of sequence

given a sequence x(n), where x(0) = 4, x(1) =3, x(2) = 2, and x(3) =1 with the last two data zero-padded as x(4) =0, and x(5) = 0, evaluate its DFT x(k)

  At what point on the x-axis is the magnetic field zero

A long wire carrying a 5.0 A current perpendicular to the xy-plane intersects the x-axis at x = -2.0 cm. A second, parallel wire carrying a 3.0 A current intersects the x-axis at x = +2.0 cm.

  What is the maximum ac peak to peak voltage input

The LM358 op amp can be a single or dual supply op-amp. This mean that it can operate with just a single supply i.e. + 5 volt or with dual supplies i.e. (+ and -) 5 volt supplies. With a non-inverting configuration with dual supplies (+5v and -5v)..

  Explain moore sequential circuit

Moore sequential circuit, A Moore sequential circuit has one input and one output.The output goes to 1 when the input sequence 111 has occurred and the output goes to 0 if the input sequence

  Calculate the hole diffusion current density versus x

The total current in a semiconductor is constant and is composed of electron drift current and hole diffusion current. The electron concentration is constant and is equal to 10^17 cm^-3. The hole concentration is given by p(x)

  How many joules of energy are stored in the battery

A double-A (AA) rechargeable battery is rated at 1.2V, 2100mA-h ( mili-amp hours) 1- how many coulombs of charge can this battery hold 2- how many joules of energy are stored in the battery

  Calculate the voltage across the 360-v winding

1-phase 2-winding transformer is rated 30 kVA, 360/90 V, 60 Hz. A source connected to the 360-V winding supplies an impedance load connected to the 120-V winding. The load absorbs 15 kVA at 0.8 p.f. lagging

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd