Design an mcm system that has a symbol period

Assignment Help Electrical Engineering
Reference no: EM131206846

a. Consider a multipath channel with a delay spread of 5 µs through which it is desired to transmit data at 500 kbps. Design an MCM system that has a symbol period at least a factor of 10 greater than the delay spread if the modulation to be used on each subcarrier is QPSK.

b. If an inverse FFT is to be used to implement this as an OFDM system, what size inverse FFT is necessary assuming that the FFT size is to be an integer power of 2?

Reference no: EM131206846

Questions Cloud

Nominal gdp to gauge economic well-being : 1. Why do economists use real GDP rather than nominal GDP to gauge economic well-being? Define the GDP deflator. 2. What is the CPI? Which do you think has a greater effect on the consumer price index: a 10 percent increase in the price of chicken,..
Conclusion for five kingdom classification : Conclusion for five kingdom classification merits and demerits.
Which ways the self-fulfilling prophecy occurred in the film : In which ways the process of perception (selection, organization, and interpretation) builds up the storyline between the LAPD officer John Ryan and his partner, and TV Director Cameron Thayer and his wife Christine?
Complete substantitive sentences : Remember to respond to at least two of your peers' postings. Initial discussion questions should contain a minimum of 150-words. Follow-up peer responses should contain a minimum of three complete substantitive sentences. Please check spelling, g..
Design an mcm system that has a symbol period : If an inverse FFT is to be used to implement this as an OFDM system, what size inverse FFT is necessary assuming that the FFT size is to be an integer power of 2?
What was the attention grabbing opening statement : Introduction: Identifying key elements of an Introduction- What was the 'attention grabbing' opening statement? Was it effective? Discuss. Did the introduction identify the background information to the essay topic
What strategies and tools were used to analyse the data : What analytical strategies and tools were used to analyse the data? Can you suggest alternative strategies and tools? How would analysing the data in a different manner alter the data presentation?
Determine the positive amplitude and peak to peak value : Find the period T. - How many cycles are shown? - What is the frequency? - Determine the positive amplitude and peak-to-peak value.
What is the maximum amount of new loans : What is the maximum amount of new loans that this bank can make? Assume that the bank makes these loans. What will the new balance sheet look like? By how much has the money supply increased or decreased?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design an inductor l to make tune by using the plastic pin

If we want to receive an FM station that broadcast on frequency = 100 MHz and we have to build a tunning circuit of LC utilizing a capacitor of 10pF. Design an inductor L to make tune by using your plastic Pin as a core for widing

  Give typical frequency response plots of singular values

Singular values and associated directions vary with frequency . -  give typical frequency response plots of singular values and indicate on the plots the bandwidth.

  Write the logic equation for microprocessor-driven function

A chemical plant needs a microprocessor-driven alarm system to warnof critical conditions in one of its chemical tanks. Thethank has four HIGH/LOW (1/0) switches that monitor temperature(T), pressure (P), fluid (F), and weight (W).

  Determine the overall error probability

The uplink SNR is 8 dB, and the downlink SNR is 5 dB, where the SNR is the signal power divided by the noise power in the bit-rate bandwidth. Determine the overall error probability.

  What type of load impedances can be matched

Determine, in general, what type of load impedances can be matched using such a circuit.

  Calculate and plot ß for a p-n-p bjt with lnp

The current amplification factor β of a BJT is very sensitive to the base width as well as to the ratio of the base doping to the emitter doping. Calculate and plot β for a p-n-p BJT with Lnp = Lpn for: (a) nn = pp and Wb/Lnp = 0.01 to 1

  Find what is total real power and reactive power produced

A three phase generator is producing power for a balanced load. Each phase provides an rms voltage of 690 V and an rms current of 1000 A. The angle between the voltage and current in each phase is 20 degrees.

  Find what is the output voltage at 75 degree

A potentiometer is wired is wired to represent a rotational range of 0-180 degree. The potentiometer is supplied with a voltage of 15 VDC. What is the output voltage at 75 degree

  Find what is the maximum amplitude of the sine wave

A non-inverting amplifier with a closed loop gain of 1000V/V is designed using an opamp having an input offset voltage of 5mV and output saturation levels of ±13V. What is the maximum amplitude of the sine wave that can be applied at the input wit..

  Design an attenuator

Determine the image impedance seen at AC - Determine the image impedance seen at BD and Verify the attenuation of your symmetrical design matches that of the asymmetric experiment by constructing and analysing the attenuators on Multisim

  Find its coefficients of arealand cubical expansion

The coefficient of linear expansion of nickel is 13 x106/°C. Find its coefficients of arealand cubical expansion

  Discuss the possible difficulty of such an approach

Discuss the possible difficulty of such an approach.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd