Design a single-section quarter-wave matching transformer

Assignment Help Electrical Engineering
Reference no: EM131105425

Design a single-section quarter-wave matching transformer to match a 350 load to a 100 line. What is the percent bandwidth of this transformer, for SWR ≤ 2? If the design frequency is 4 GHz, sketch the layout of a microstrip circuit, including dimensions, to implement this matching transformer. Assume the substrate is 0.159 cm thick, with a relative permittivity of 2.2.

Reference no: EM131105425

Questions Cloud

What amount should oak city report for property tax revenues : What amount should Oak City report for 2012 property tax revenues in the Statement of Revenues, Expenditures, and Changes in Fund Balances prepared for governmental funds?
What types of contractual obligations must be disclosed : What types of contractual obligations must be disclosed in great detail in the notes to the balance sheet?
Consequences of a declining dollar on fluor corporation : Assess the likely consequences of a declining dollar on Fluor Corporation, the international construction- engineering contractor based in Irvine, California.
Compare the economies and monetary policies of two countries : Compare and contrast the economies and monetary policies of the two countries that you have researched. Make at least two recommendations as to the primary manner in which both countries could improve their economy and / or monetary policies.
Design a single-section quarter-wave matching transformer : If the design frequency is 4 GHz, sketch the layout of a microstrip circuit, including dimensions, to implement this matching transformer. Assume the substrate is 0.159 cm thick, with a relative permittivity of 2.2.
Differentiate between the following types of markets : What is a market? Differentiate between the following types of markets: physical asset markets versus financial asset markets, spot markets versus futures markets, money markets versus capital markets, primary markets versus secondary markets, and pu..
Formulate a linear programming mode : (b) Use the simplex method to solve this model. Use the resulting optimal solution to identify an optimal policy.
What lacked in the provision of the plaintiff kiplagat : Referring to the Justice Tunoi v Kiplagat case, what lacked in the provision of the plaintiff kiplagat that saw the case terminated?
What amount should elm debit to budgetary fund balance : What amount should Elm debit (credit) to Budgetary Fund Balance-Reserved for Encumbrances after the supplies and invoice were received?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the required resistor value of rc high-pass filter

A first-order RC high-pass filter has a cutoff frequency of fc = 2400 Hz and the capacitor value of C = 47 nF. What is the required resistor value

  Draw the equivalent circuit referred

Consider the transformer to deliver its rated kilovoltamperes at 0.80 power factor lagging to a load on the low-voltage side with 240 V across the load. Find the highside terminal voltage.

  Do you have the solutions for digital processing of speech

do you have the solutions for digital processing of speech signals book of rabiner and schafer.questions 2.14 and 2.17

  What will the output voltage be for a strain of 1000

A resistor on a Wheatstone bridge is replaced with a strain gage which has a nominal resistance of 120 Ohms and a gage factor of 2.06. The remaining resistors on this quarter-bridge Wheatstone bridge circuit are 120 Ohm fixed resistors.

  What are the possible power levels pi at the outputs

Suppose the above device is to be used as an 8-way power splitter (let's say only the top-most input is used). Let the input power be P. Assuming a cross-coupling coefficient of f and ignoring excess losses, what are the possible power levels Pi a..

  Determine es and os for this system

Let P ⊆Rn be a convex set, and let x ε Rn with TP (x) 6= Φ. Prove that TP (x) is a convex cone.

  What is the nature of the performance gain

Suppose the gain between the transmit antenna and each of the receive antennas is constant, equal to 1. What is the capacity of the channel? What is the performance gain compared to a single receive antenna system? What is the nature of the perfor..

  Determine what is the current on the surface of conductor

A plane waveis obliquely incident on a perfectly conducting half-space. The magnetic field is perpendicular to the plane ofincidence. The incident Ehas anamplitude of 1V/m,and the incident angle is θi.

  What is range of resistance that expected to measure

The tolerance on resistors is + 2σ by convention, i.e.,approximately 95% confidence level. With 95% confidence, what is the range of resistance that you would expect to measure experimentally for resistors with the following four color bands

  Determine what is the total three-phase load

A factory is to be supplied with 408Y/277 3 phase, 4 wire electrical service. The total estimated single-phase load is 25 kW, at .9 lagging power factor. The total estimated three-phase load is 250 kW at .85 lagging power factor.

  Find the per-unit reactance of each generator

Two generators are connected in parallel to the same bus bar and each has an inductive reactance of 10% on rating. Generator 1 is rated 2,500 kVA and 2.4 kV, and generator 2 is rated 5,000 kVA and 2.4 kV.

  Find the maximum frequency for nyquist sampling rate

Nyquist sampling rate condition and aliasing Consider the signal: X(t) = sin(0.5)/0.5t a.)Find the Fourier transform X(Ω) of x(t). b.)Is x(t) band limited. If so, find its maximum frequency Ωmax.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd