Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design a signal conditioning circuit for a K-type thermocouple, which produces output voltage of 0V-5V using a three terminal solid-state temperature sensor for reference junction compensation. The sensitivity of the sensor is 4mV/C. Use 0C and 100C as design base points. (Problem 4.29 p220)
a) Assuming the reference junction temperature TR is zero; derive the expression for signal conditioner output voltage V0 in terms of the thermocouple voltage Vth.
b) When T(r) not 0, develop an expression for V0 in term of measurement junction voltage Vm and reference junction temperature TR, utilizing reference junction compensation.
Sketch a block diagram which implements the solution derived in (b), labeling each block with appropriate name and corresponding gain. Each signal/variable in the diagram must be identified.
When the two windings are connected to a a.c supply of 50hz, the field current is 0.1A, the armature current is 100A and the phase difference between them is 60 degree. calculate the average torque and maximum torque.
Saw on internet some equations to convert from frequency in hertz to mph. Some equations need a gear ratio while others do not. I found the equation mph = circumference * RPM * 60.
Once a week a wagon driver leaves his hut and drives his wagon to the river dock to pick up supplies for his town. At 4:05 PM, one-fifth of the way to the dock, he passes the Temple. At 4:15 PM, one-third of the way, he passes the Preetam-Da-Dhaba..
You are evaluating the feasibility of adding an injection molder to fabricate plastic sporks (everybody’s favorite harmless utensil) for the US Facility for the Criminally Insane. An injection molder will cost $1,200,000 installed.
An abrupt p-n junction has a doping concentration of 1015, 1016, or 1017 cm-3 on the lightly doped n-side and of 1019 cm-3 on the heavily doped p-side. Obtain series of curves of 1/C2 versus V, where V ranges from -4 to 0V in steps of 0.5V.
What is the smallest number of samples that could be collected in order to know for sure whether or not the 1000Hz component is present? Assume you are using a Rectangular window.
Each equation above describes a field that is distributed sinusoidally and whose amplitude varies sinusoidally with time (a pulsating field). Prove for the resultant magnetic flux density in the air gap (a) at any given t
An amplifier has a gain of 10 and follow a bandpass filter filter where the loss in the in the center of the bandpass is 0.05. What is the combined gain/loss of the two cascaded blocks at the center frequency of the filter
In a circuit, there is a resister, a conductor and a capacitor connected to voltage source. R = 25 ohms, L = 20 milliH, and C = 50 microF. a) Find the total impedance of the network if the frequency is 60 Hz.
A silica fiber has an outer diameter of 125 micro meter. What is the total volume of silica for a 1-km length? This fiber is wound on a spool whose unloaded diameter is 20 em. The spool height is 10 em. Compute the diameter of the fully loaded spo..
A dc separately excited generator runs at 1200 rpm. the rated current and voltages are 100 A at 240 V. The armature resistance is 0.15 (ohms). The open circuit magnetization characteristics at 1200 rpm are
The relative dielectric constant of the printed circuit board (PCB) is 4 and the microstrip lines have a characteristic impedance of 80W. The length of the microstrip lines are 30mm and 45mm, respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd