Design a minimum two-level nor-gate network to realize

Assignment Help Electrical Engineering
Reference no: EM13268259

Given the function F(a,b,c,d)=a'b+ad'+ab'

a) Design a minimum two-level NOR-gate network to realize the above function.

b) Design a minimum three-level NOR-gate network to realize the above function.

Reference no: EM13268259

Questions Cloud

Calculate copper and core losses in transformer at condition : A 150-MVA 15/200-kV single-phase power transformer has a 0.018ohm resistance and a 0.075ohm reactance. The magnetizing impedance is j80 per unit. a.) Find the equivalent circuit referred to the low-voltage side of this transformer.
Explain how to make a solution of hydrogen peroxide : How do you figure out how to make a solution of 50mL of 3.6M hydrogen peroxide (H2O2) from 30% hydrogen peroxide
Find the focal length of a correctly prescribed contact lens : An eye has trouble seeing an object closer than 60 cm but needs to see objects at 25 cm from it. find the focal length of a correctly prescribed contact lens
What is the incremental free cash flow for year one : The new machine will be depreciated using the simplified straight-line method over its 5 year useful life, resulting in expected to increase by $10000 at the inception of the project, but this amount will be recaptured at the end of year five. Wha..
Design a minimum two-level nor-gate network to realize : Given the function F(a,b,c,d)=a'b+ad'+ab' a) Design a minimum two-level NOR-gate network to realize the above function. b) Design a minimum three-level NOR-gate network to realize the above function.
How much heat flows in to our out of the gas : a cylinder contains 4.0moles of a monoatomic gas at an initial temp of 27deg C. How much heat flows in to our out of the gas
Define what is the mass number of the other isotope : Naturally occurring gallium consists of two isotopes. One of those isotopes is 71Ga with an isotopic mass of 70.9247050 amu and an abundance of 39.892%. What is the mass number of the other isotope
Critically review your own facebook : What information is appropriate to place in these forums and what shouldn't be shared and why - should employers have the right to seek out these personal postings and make decisions about you based on what they read?
What will be the voltage measured across the motor terminals : Suppose a resistor whose value is equal to the motor resistance is connected across the motor terminals and the motor is spun at 200 RPMs. What will be the voltage measured across the motor terminals

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the power dissipated in the mosfet

(b) Calculate the power dissipated in the MOSFET when the lamp is operating at its rated current. (c) The maximum output current available from the logic system is 30mA. Explain why an NPN transistor would be unsuitable for this appli..

  Design a appropriate lter to lter out component of the input

Let the component at Omega(C) = 2pi* 3000 be the corrupting signal. Design an appropriate lter to lter out this component of the input. You can use fir1 command for this. Plot the frequency response of this lter.

  What approximate minimum ber is required for voice signals

What approximate minimum BER is required for voice signals, data signals and what is the approximate BER level for the optical fiber systems ?

  At what temperature are the two carrier densities equal

At what temperature are the two carrier densities equal?

  Find the angles e1 and e2 make with the interface

Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x 0. Find: a) E2 for x

  Calculate total charge on plates and potential gradient

The capacitance of a capacitor formed by two parallel metal plates each 200 cm2 in area separated by a dielectric 4 mm thick is 0.0004 microfarads. A p.d. of 20,000 V is applied. Calculate (a) the total charge on the plates

  Find the input impedance into this line at z

A transmission line with no loss, with Z0= 60 ohms, is operated at 60MHz. The velocity on the line is c. The line is soldered to a ground connection at z=0. Find the input impedance into this line at z= -1.25 meters

  How big will be rms value of voltage across coil nd resistor

how big will be inductance of coil if it is connected in series with resistor 30 omega on AC circuit with input voltage with RMS value U1=(220+2*1.7) V and frequency 50 Hz if power factor of the circuit is 0.6

  Determine size of capacitor that must be placed in parallel

A 120 Veff motor draws 1.5 kVA at a lagging power factor of .85. Determine the size of the capacitor that must be placed in parallel with the motor for a power factor of 1.

  Design a multi-function unit with four functions chosen

Design a multi-function unit with 4 functions chosen using select inputs s1s0. The unit has two 2-bit inputs (A = a1,a0 and B = b1,b0) and 4-bit output (z3,z2,z1,z0). The unit performs A+B (s1s0 = 00), AB (s1s0 = 01), A2+B (s1s0 = 10)

  Explain how to design a regulated dc power supply

Design a regulated DC power supply. You will have for input a 110 V input source at a frequency of 60 Hz. The Zener diode to use is the 1N4733A (which is available in the lab). The output voltage is to be 5.1 V with a load resistance above 2.2K.

  How big will be rated power of motor for starting current

How big will be rated power of the motor if starting current at star-connection and phase to phase voltage of the supply 380 V is (150+17) A. the ratio of starting current for motor is 7 Ir efficiency factor is 0.85 but cos f =0.8

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd