Design a loadable d flip-flop with an active low input load

Assignment Help Electrical Engineering
Reference no: EM13277524

The characteristic equations for a D flip-flop determine that the output Q is updated to either 0 or 1 after each clock cycle. A loadable D flip-flop has one additional input Load that allows data to be stored in the flip-flop for more than a single clock cycle. Design a loadable D flip-flop with an active low input Load using a normal D flip-flop and some combinational logic. Use the characteristic equations for a D flop-flop as a starting point. When the input signal Load=0, the flip-flop functions as a normal D flip-flop. When the input signal Load=1, the output Q stays at it's previous value.

Reference no: EM13277524

Questions Cloud

What are public opinions on technology such as media : What are the public opinions on technology such as the media, consumers and community? What is your assessment of how effective the initial planning and risk assessment was to the implementation and usage of the technology?
Find what is the probabilty that is black will be valid code : A date link protocal uses the CRC16 polynomail for error detection A) suppose the data block (including the 16 check bits) has n=1000 bits how many possible received black are there. B)On a particular transmission a lot of errors occur in the receive..
How do changes in endothelial and immune cell function : How do changes in endothelial and immune cell function contribute to cancer and name two carcinogens and how each contributes to a specific type of cancer.
Determine the acceleration of the electron : In an electron microscope, there is an electron gun that contains two charged metallic plates 2.90 cm apart. Determine the acceleration of the electron
Design a loadable d flip-flop with an active low input load : The characteristic equations for a D flip-flop determine that the output Q is updated to either 0 or 1 after each clock cycle. A loadable D flip-flop has one additional input Load that allows data to be stored in the flip-flop for more than a sing..
Find the speed of the four cars after the collision : A railroad car of mass 2.40 multiply.gif 104 kg is moving with a speed of 3.82 m/s. find the speed of the four cars after the collision
Determine what is the net electric field in vector notation : two particles are fixed to anhe par x axis ;particle 1 of charge -2.00*10^-7c at x=6.00cm and particle 2 of charge +2.00*10^-7 at x=21.0cm. midway of particles, what is their net electric field in vector notation
What are some political implications and influences : What are some alternative perspectives from experts on technology? What are some political implications and influences?
Define water flowing through pipes of carbon steel must : Water flowing through pipes of carbon steel must be kept at PH 5 or greater than limit corrosion if an 8.0 *10^3 Ib/hr water stream contains 10 ppm sulfuric acid and 0.015% acetic acid, how many pounds per hour of sodium acetate trihydrate

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the expression of the allowed energy levels

Using the time independent one dimensional Schrodinger equation, find the expression of the allowed energy levels for an electron in infinite potential well of width Δz= L (i.e. solve the differential equation and apply B.C. to obtain En)

  Write down the expression for the frequency-dependent

Write down the expression for the frequency-dependent open-loop gain of an operational amplifier. Sketch the magnitude of the open-loop gain of an operational amplifier as a function of frequency. Explain what is meant by a `single-lag' response o..

  Evaluate the correlation between the two signatures

Sketch the baseband signals for the two users when user 1 sends the bits 011, and user 2 sends the bits 101. Add the signals for the first bit only, and show that the output of the correlator for user 1 is -4, corresponding to a 0

  Design fir linear phase filter by approximating the response

Design a FIR linear phase filter by approximating the ideal frequency reponse (H^{d}(e^{jwt})=1, for |w|

  What is the baseline and calibration curve for the sensor

Draw a strain gauge circuit and its external components to attach to a conveyor mounted only at the ends to measure the load at the center of the conveyor. What type of testing would you need to do to establish a baseline and calibration curve for..

  What other energy device must be included in solar system

The amount of sunshine on a horizontal surface at the equator is 5kWh/m2/day. Suppose a house is to run entirely off grid on solar electricity alone using a high performance silicon photovoltaic module with specifications shown below: Maximum powe..

  What is approximate time taken by the car to reach electrode

A charge of 4 micro-Coulomb is applied to the surface of the car. If the car travels a distance of 2 meter between the two electrodes, and if the mass of the car is 200 grams, then what is the approximate time taken by the car to reach the second ..

  Determine the highest frequency of the analog signal

The basic sampling rate for the compact disc (CD) recording industry has been set at 44.1 kHz. (a) Determine the highest frequency of the analog signal that could theoretically be reconstructed from this sampling rate.

  Find what is lightbulbs design life in days

A 60-watt outdoor lightbulb is advertised as having an average life (i.e. MTTF) of 1,000 operating hours. However, experience has shown that it will also fail on demand an average of once every 120 cycles.

  Draw ac equivalent ckt with load impedance element equated

A three phase 4.157kv 60hz power system serves a 2880kva load pf=.8 lagging. Draw the ac equivalent circuit with load impedance element equated. The load is delta connected. solve for all the current (6 total).

  Write a testbench stimulus

Write a testbench stimulus for the below 8-bit Shift-Left Register with Positive-Edge Clock, Serial In and Serial Out. Start with all ones after the 8th=bit shifted to the left all zeros.

  Find the vswr coefficient of a 50 ohm transmission line

A 50 ohm transmission line is terminated to the load (60-40j) ohm. How far from the load, a short ckt stub of a fix length of λ/8 needs to be placed so the minimum voltage standing wave ratio (VSWR) between generator and stub achieved. Find the VS..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd