Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR)
The behavior of the garage door controller is as follows:- there is a single button in the garage, and a single button remote control.- when the button is pushed the door will move up or down.- if the button is pushed once while moving, the door will stop, a second push will start motion again in the opposite direction.- there are top/bottom limit switches to stop the motion of the door.- there is a light beam across the bottom of the door. If the beam is cut while the door is closing the door will stop and reverse.- there is a garage light that will be on for 5 minutes after the door opens or closes.-there is a cell phone open and close buttons using Wi-Fi
Gov. Expend. Tax rev. 170 90 450 170 110 550 170 130 650 170 150 750 170 170 850 Refer to the accompanying table for Waxwania. a. What is the marginal tax rate in Waxwania percent The average tax rate
Draw an absorption spectrum of leucoindigo. What color is absorbed by leucoindigo? Draw a simple energy level diagram of leucoindigo. Calculate the energy difference between energy levels.
Discuss additional behavioral implications of planning and control when a company's management employs an imposed budgetary approach and a participative budgetary approach.
determine the work and heat transfer, each in kJ. sketch the process on p-v and T-s coordinates. Associate the work and heat transfer with areas on these diagrams.
Consider a supersonic wind tunnel with test section Mach number of 2 and fixed geometry diffuser designed to operate with minimum stagnation pressure losses (smallest diffuser area).
The work function of copper is 437 kj/mol. Calculate the KE of the ejected electron if the frequency of light is 1.50*10^(15) Hz.
Money deposited for a term is not left in bank vaults but is loaned out by the banks (subject to mininum cash reserve requirements). This means that a dollar on deposit can flow back into the banking system one or more times.
calculate the largest semicircular surface flaw oriented along the axis of the bores that could withstand a fluid pressure of 50MPa.
the air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. if the air is at 13.4 psia absolute and 70 degrees C and the reading of the differential pressure gage is 0.15 psi, determine the air velocit..
A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.
Calculate the static thrust of the turbojet engine having mass flow 88lbm/sec the ratio of air and fuel mass flowing into the turbojet is 50:1 and it's exhaust plane the velocity is 1640 ft/sec and pressure is same as ambient pressure?
Determine the specified data for water at the states indicated and locate each state on a P-v and T-v diagram.
The assessment to design a substation and the associated protection System.
Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.
The diameter of the tube is 13 cm and its length is 60 m. Determine the overall heat transfer coefficient of this heat exchanger using (a) LMTD and (b) -NTU method.
Sketch the T-s diagram for the cycle (put labels and appropriate information)
Given a simulator or actual device, identify if a control loop is in control or out of control and identify the information used to make the decision
If the filling is done rapidly, calculate the final temperature in the small cylinder, (a) assume that oxygen is an ideal gas with Cv= 5R/2 and (b) using accurate thermodynamic data for oxygen.
Advanced Stress Analysis Assignment
Find the stoichiometric A/F ratio (by mass) for the combustion of benzene (C6H6). Compute the actual A/F ratio and do a wet and dry analysis of the products by volume at a mixture strength of 95%.
The heating is to be done in a mixing tank by direct injection of the steam, all of which condenses. Determine the two inlet mass flows needed to meet the desired hot water flow rate.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: info@expertsmind.com
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd