User Account

All Pages

Design a full wave unregulated dc power supply

Assignment Help Electrical Engineering
Reference no: EM13266941

Design a full wave unregulated dc power supply having an input of 220 V rms 60 Hz and an output voltage maximum of 19.5 V and a minimum of 15 V. This power supply will be needed to provide power to a load which requires a maximum current of 500 mA. Assume the diode and transformer are ideal.
a. Circuit Configuration
b. Transformer winding ratio
c. Capacitor size

Reference no: EM13266941

Questions Cloud

Determine what is the integrator time constant : An opamp based integrator is measured at 1KHz to have a voltage gain of -100 V/V. At what frequency is its gain reduced to -1V/V. And, what is the integrator time constant
Determine the mass of the second block : A block of mass 200g, sliding with a speed of 12 cm/sec on a smooth level surface, makes a head-on, elastic collision with a block of unknown mass, Determine the mass of the second block
Explain the stabilization of a half-filled of shell : The stabilization of a half-filled of shell is even more pronounced than that of the p subshell. Why
What are some of the risks and cost considerations : What are some of the risks and cost considerations associated with each of these alternative financing strategies?
Design a full wave unregulated dc power supply : Design a full wave unregulated dc power supply having an input of 220 V rms 60 Hz and an output voltage maximum of 19.5 V and a minimum of 15 V. This power supply will be needed to provide power to a load which requires a maximum current
Explain efficiency and minimum possible rate of heat discard : Find the maximum possible thermal efficiency and minimum possible rate of heat discard. If the actual efficiency is 60% of the maximum and the river has a flowrate of 165 m 3 /s, what is the expected temperature rise of the river
What must be the thickness of the liquid layer : What must be the thickness of the liquid layer if normally incident light with? = 504 nm in air is to be strongly reflected
Briefly describe your dream job with an organization : Briefly describe your "dream job" with an organization for which you would like to work and create a rewards and compensation package for this position that would both attract skilled workers (you) yet control costs.
Find the largest possible number of independant vectors : Find the largest possible number of independant vectors v1=column[1 -1 0 0] v2= column[1 0 -1 0] v3=column[ 1 0 0 -1] v4= column[ 0 1 -1 0] v5= column[0 1 0 -1] v6= coolumn[ 0 0 1 -1] note all are column vectors

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Approve that we wished to match an admittance

Suppose that we wished to match an admittance using a double-stub tuner where the stubs are lambda/4 apart. For what range of admittance values can

  Express logic relationship between inputs and outputs

give three methods that are used to express logic relationship between inputs and outputs of a logic gate, for example a three-inputs NOR gate.

  Estimate the ratio of powers generated by the same speed

Suppose a turbine is used for generating electricity, estimate the ratio of powers generated by the same speed water and air. (Water density=1g/cm3, air density =1.2kg/m3)

  Which should be the signal power in the given case

A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW

  What are the advantages of using a counter

In a Built in Self Test, for a combinational logic system, what are the advantages of using a counter instead of an ALFSR to generate testing vectors for 2 cases.

  Calculate the starting torque of the motor

A dc series motor has a armature current of 10A at full load. The motor terminal voltage is 300V. The armature and field resistances are 2 ohm and 3 ohm respecitively. The motor speed at full load is 250 rpm. Calculate the starting torque of the m..

  Explain power factor

Power Factor, A single phase electric motor has an output power of 10 kW and an efficiency of 90% at full load. The motor is fed from a 240 V supply via a cable that has a resistance of 10 milli ohms per metre length.

  Calculate the number of calls

i) Calculate the number of calls/hour/cell and the number of calls/hours/km2 ii) Calculate the number of users/hour/cell and the number of users/hours/channel iii) Find the modulation frequency for this system.

  How long after sudden dark-to-light flash before cell output

A photocell with a 35-ms time constant is used to measure light flashes. How long after a sudden dark-to-light flash before the cell output is 80% of the final level

  Calculate dual film stress nd the stress of the nitride film

A 200 nm oxide film is deposited on a 500 m thick bare silicon wafer that has a radius of curvature of 300 m. After deposition, the radius is measured to be 200 m. A 600 nm nitride film is now deposited on the oxide

  Calculate gf using outside diameter of the pipe

A true centrifugal casting operation is to be performed in a horizontal configuration to make cast iron pipe sections. The sections will have a length = 42.0 in, outside diameter = 8.0 in, and a wall thickness = .50 in

  What would be needed to add to be able to make the circuit

Suppose you need an 8-bit counter, and an 8-bit shift register. How would you go about creating these. Could you create them using the counter and shift register you created already.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd