Design a full-wave rectifier to provide a dc output

Assignment Help Electrical Engineering
Reference no: EM13293115

Design a full-wave rectifier to provide a dc output of 28V at acurrent of 4A, with a ripple of not more than 3%. A linevoltage of 120V (rms), 60Hz is available.

Reference no: EM13293115

Questions Cloud

Compute the density of a solution of benzene : Calculate the density of a solution of benzene and toluene mixed at 1:1 weight ratio at 20 degree C and 1 atm, given that ?(benzene) = 0.8790 g/cm^3 and ?(toluene) = 0.8668 g/cm^3 at 20 degree C and 1 atm.
What is scientific software effective annual rate : What is Scientific Software's effective annual rate of interest if it borrows $100,000 for 12 months? For 6 months? For 3 months? (Note: Assume a 365- day year and a prime rate that remains at 8.5% during the life of the loan.)
Would it increase firm profitability to give up discount : If the firm had made a purchase of $100,000 for which it had been given terms of 2/10 net 30, would it increase the firm's profitability to give up the discount and not borrow as recommended in part b? Why or why not?
Explain a mixture of kcl and kclo3 : A mixture of KCl and KClO3 weighing 1.55 grams was heated the dry O2 generated occupied 1.4x102 ml at STP. What percent of the original mixture was KClO3 which decomposes as follows
Design a full-wave rectifier to provide a dc output : Design a full-wave rectifier to provide a dc output of 28V at a current of 4A, with a ripple of not more than 3%. A linevoltage of 120V (rms), 60Hz is available.
Estimate the distance between the charges : A positive charge +q1 is located to the left of a negative charge -q2. On a line passing though the two charges, What is the distance between the charges
How to determine the line current at starting : A 3-phase cage rotor induction motor has a full load slip at 5% . The standstill current at rated voltage is 6.5 times full load current . Find autotransformer tapping to give full load torque at starting and also find the line current at starting..
Evaluate the proposed relaxation : Evaluate the proposed relaxation, and make a recommendation to the firm. (Note: Assume a 365-day year.)
Explain chlorine measured at the same conditions : A mixture is prepared from 15.0 l of ammonia and 15.0 l chlorine measured at the same conditions these compounds react according to the following equation 2NH3+3Cl2---> N2+6HCl When the reaction is completed what is the volume of each gas

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the output of the system described by equations

Determine the output of the system described by the following difference equations with input and initial conditions as specified: y[n]+6y[n-1]-16y[n-2]=3x[n] x[n]=((-1)^n)*u[n] y[-1]=2 y[-2]=-1

  How to symbolize that above system as a logic function

The vaultdoor will be equipped with a vibration sensor that will cause aswitch to close it the vault is disturbed, ans a switch will bemounted on the bank door in such a way that i will close wheneverthe bank door is opened.

  How hot would a conventional pipe have to get to burst

How hot would a conventional pipe have to get to burst and why Does it vary according to what material the pipe is made of Which are the strongest What are weak ones

  What magnitude of dipole strength has to be associated

A certain sample of pure quartz has a dielectric constant of 3.8, dielectric strength of 1.0 kV/0.0010 in, and a density of 2.6 Mg/m3. Assume the number density of dipoles in quartz is the same as the number density of SiO2 units.

  Design counter using d flip flips and the one hot method

if x = 0, the counter counts 1,2,3,4,5,6,7 and repeats. if x = 1, the counter counts 7,6,5,4,3,2,1 and repeats. The counter should be designed using D Flip FLips and the one hot method. Draw the asm chart and final logic diagram.

  What are the conditions in terms of electrical parameters

Is it possible to interface an IC with a different technology such as TTL to HCS12 ports What are the conditions in terms of electrical parameters that need to be satisfied for this purpose

  Find two renewable energy application for converters

Find two renewable energy application where ac/dc converters are used. Explain qualitatively the role of the converter in the application

  Distinguish the synchronization sequence

Suppose that the sequence 110010011 is used as a synchronization sequence preamble to a data packet. Propose a method that can be used to allow the channel to distinguish the synchronization sequence from an identical data sequence within the pack..

  How a rare disease affects individuals in the population

Now assume that the doctor knows that 1 in 100 individuals with symptom G will have the rare disease, and he only orders the test when individuals have symptom G. Given that one of the doctor's patients tests positive.

  What are earnings as a percentage of the final retail price

In the electronics business, mark-up is in the order of 100% to 130% at each level of middleman. Let's say that it is 100%. Let's further say that your product passes through three levels of middleman, that your product is produced in accordance

  Calculate armature voltage va to be applied in steady state

If the motor is driving a load whose torque requirement remains constant at 3Nm, independent of speed. Calculate the armature voltage Va to be applied in steady state, if the load to be driven at 1500RPM.

  Determine what are the minterms of f and g

The minterms of functions F(A,B,C) and G(A,B,C) are Σ m(1,3,5,6) and Σ m(1,4,5,7). What are the minterms of F' and G', and what are the maxterms of F+G and FG

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd