Design a dc power supply that provides energy absorber

Assignment Help Electrical Engineering
Reference no: EM13227345

Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc) and use the smallest values that will do the job. If you use diodes, assume they are ideal. Draw the complete circuit, including the load.

Reference no: EM13227345

Questions Cloud

How many ram and rom chips are needed to employ ram chips : A computer employs RAM chips of 256 x 8and ROM chips of 1024 x 8. The computer system needs 2K bytes of RAM, 4K bytes of ROM, and four interface units, each with four registers. A memory-mapped I/0 configuration is used.
Complete the leadership in action : Complete the Leadership in Action: David Neeleman Reinvents Airlines. Answering the case questions involves identifying relevant facts from the case, applying the chapter concepts to the case, and answering each question completely.
Define the formula of sedative demerol hydrochloride : Cyclopropane, C3H6, is an anesthetic given by inhalation. How many grams are in 0.30 mole of cyclopropane? The sedative Demerol hydrochloride has the formula C15H22ClNO2. How many grams are in 2.2x10^-2 mole of Demerol hydrochlorde?
What is the maximum utilization of days : A nursing home contracts with an HMO for skilled nursing care at $2.00 PMPM. If costs are expected to average $120 per day, what is the maximum utilization of days per 1,000 members that the nursing home can experience before it begins to lose mon..
Design a dc power supply that provides energy absorber : Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc).
How much must the member pay : An HMO has a Point of Service (POS) option for its members, but will pay only 80 percent of approved charges. If a member goes out of network for a medical procedure with a charge of $2,000, of which $1,200 is approved, how much must the member pa..
Design a circuit that takes an input signal that can swing : For input signal voltages between these limits, the input should pass unaltered to the output. The peak current drawn from the input source may not exceed 1mA. You may use any circuit component we've studied except opamps.
At what value of annual cash flow would beverly : If Beverly Enterprises has a cost of capital equal to 15 percent, at what value of annual cash flow would Beverly Enterprises be likely to sell the nursing home?
State what effect will increasing the volume of the reaction : Consider the following reaction at equilibrium. what effect will increasing the volume of the reaction mixture have on the system?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Why developing software for wireless devices is challenging

Why developing software for wireless devices is challenging? List and briefly describe the two (2) reasons given in your textbook for why developing software for wireless devices is challenging.

  Find the capacitance and inductance of the matching network

The amplifier is connected to the handset antenna which has an impedance of 35 + j10 at one unspecified operating frequency. Find the inductive reactance and capacitive reactance needed to match the transmitter output to the antenna

  Find the joint probability density function of y1 and y2

X1 and X2 are two independent Gaussian random variables each with mean zero and unit variance.

  Estimate of the maximum fundamental operating frequency

Using the LM555 data sheet, make an estimate of the maximum fundamental operating frequency in the astable mode.

  Calculate the signal to noise ratio given rms noise voltage

1. Given R = 50Kohm and C = 100nF what is the frequency of oscillation 2. Given a required frequency of oscillation of f = 10kHz and R = 8kohm, what should the value of C be Calculate the signal to noise ratio given RMS Noise Voltage = 20mV and RMS S..

  What is energy stored at switch closed

For a RL circuit, write a diffedrential equation in which the only time dependant quantity is current (use Kirchoff's loop). Derive an expression for current, i(t), in terms of L,R, and Vo. If Vo=5V, R=2.5 ohms, L=100 nH

  Define design with multiplexer

Define Design with Multiplexer, Design a circuit using one 16 TO 1 multiplexer with W, X,Y,Z on the control inputs

  Draw the circuit

A majority function is generated in a combinational circuit when the output is equal to 1 if the input variables have more 1's than 0's. The output is 0 otherwise. Design a 3-input (A, B, C) majority function. Use K-maps to simplify the circuit. D..

  What are the drawbacks to developing resources offshore

What are the drawbacks to developing resources offshore?

  What would be the power spectral density of thermal noise

On Earth, we assume normal room temperature is 293 degrees Kelvin. From this, we find that the power spectral density of thermal noise is -174 dBm/Hz. On Venus, the average surface temperature is 462 degrees Celcius.

  Explain resistance of headlights

Resistance of Headlights, A 24-volt automotive battery is connected to two headlights, such that the two loads are in parallel

  What is difference between multiplexing and multiple access

What is the difference between multiplexing and multiple access?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd