Design a compound reverted spur gear train

Assignment Help Mechanical Engineering
Reference no: EM131392875

1. Design a compound, reverted, spur gear train for a ratio of 75:1 and diametral pitch of 12. Specify pitch diameters and numbers of teeth. Sketch the train to scale.

2. Design a compound, reverted, spur gear train for a ratio of 7: 1 and diametral pitch of 4. Specify pitch diameters and numbers of teeth. Sketch the train to scale.

Reference no: EM131392875

Questions Cloud

Find an equation relating input current to output voltage : A 4- to 20-mA control signal is loaded by a 100 Ω resistor and must produce a 20- to 40-V motor drive signal. Find an equation relating the input current to the output voltage.
Explain why the cds cell could not be used here also : A photodiode with the characteristics given in Figure b will be used to measure light intensity after the light source is triggered. Explain why the CdS cell could not be used here also.
Calculate the contact ratio : Design a simple, spur gear train for a ratio of +8: 1 and diametral pitch of 6. Specify pitch diameters and numbers of teeth. Calculate the contact ratio.
What stages were most challenging and why : Discuss the influence the decision-making process had on the outcome. Evaluate the effectiveness of the process. What stages were most challenging and why.
Design a compound reverted spur gear train : Design a compound, reverted, spur gear train for a ratio of 7: 1 and diametral pitch of 4. Specify pitch diameters and numbers of teeth. Sketch the train to scale.
Discuss about the cultural autobiography : Begin by defining individuals that you consider family members. This includes, for example, parents or guardians, siblings and/or grandparents. Important information about these individuals includes places of birth, travel (if any), age, spiritual..
Design a compound reverted spur gear transmission : Design a compound, reverted, spur gear transmission which will give two shiftable ratios of +5: 1 forward and -3.5:1 reverse with diametral pitch of 6. Specify pitch diameters and numbers of teeth. Sketch the train to scale.
Design signal conditioning : Design signal conditioning so that the distance from 0.0 to 5.0 m is converted to an 8-bit digital signal. Use an 8-bit unipolar ADC with a 10.0-V reference.
Firm is able to discriminate between the two markets : The firm is able to discriminate between the two markets. What quantities are sold in the two markets? What price is charged in each market?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Frictionless piston undergoes a polytrophic process

Air (ideal gas) inside a cylinder filled with a frictionless piston undergoes a polytrophic process having an exponent n = 1.33. The initial pressure of the air is 3.34 MPa and the T (final) is 750 K and during the process the volume of the air is in..

  Interruption of electrical power

Homeowners concerned about interruption of electrical power from their local utility because of weather-related and utility system outages can acquire a standby generator that produces electricity using the home's existing natural gas or liquid pr..

  Assuming the pressure transducer is highly linear perform a

a pressure tranducer outputs 0.23 volts at 2.39 psi and 4.71 volts at 28.13 psi. assuming the pressure transducer is

  The corresponding mass flow rates not the original

incoming air flow of 200 m3h at a temperature of 20oc and a humidity ratio of 0.012 kgvkga is mixed in a chamber with

  Engineering stress-strain curve up

The area under an engineering stress-strain curve up to fracture is the en- ergy/volume. The area under a true stress-strain curve up to fracture is also the energy/volume. If the specimen necks, these two areas are not equal.

  A load p 4000 lb acting at a point a of a beam produces

a load p 4000 lb acting at a point a of a beam produces 0.25 in at point b and 0.75 in at point c of the beam. find

  The inlet temperature is 1000 k and the exhaust pressure is

a small air turbine with an isentropic efficiency of 80 should produce 270 kjkgof work. the inlet temperature is 1000 k

  List the advantages and disadvantages of pwm

Indicate how PWM is useful in the control of dc motors. List the advantages and disadvantages of PWM.

  A piston-cylinder device with a free floating piston

a piston-cylinder device with a free floating piston contains 2 kg of water as a saturated liquid with a pressure of

  Assuming that the natural gas may be approximated as pure

compressed natural gas is stored in a spherical tank 8 meters in diameter at ambient temperature 25 degc and at a

  How much energy was input to the motor to perform this task

a compressor raises the pressure of 3kg of air gamma 1.4 adiabatically from 100kpa 288k to 450kpa. the electric motor

  What is the motion of the arm

Sun S2 is fixed. All gears have the same pitch. For each clockwise revolution of S1, what is the motion of the arm?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd