Design a combinational circuit that compares two numbers

Assignment Help Electrical Engineering
Reference no: EM13263864

Design a combinational circuit that compares two 4-bit numbers to check if they are equal. The circuit output is equal to 1 if the two numbers are equal and 0 otherwise.

Reference no: EM13263864

Questions Cloud

What is the pv of the project : a project has a forecast cash flow of $128 in 1 year and $139 in year 2. The interest rate is 7%, the estimated risk premium on the market is 12.00% and the project has a beta of .68.
Determine the boolean function that multiplexer implements : An 8x1 multiplexer has inputs A, B, and C connected to the selection inputs S2, S1, and S0, respectively. The data inputs I0 through I7, are as follows: I1 = I2 = I7 = 0; I3 = I5 = 1; I0 = I4 = D; and I6 = D'. Determine the Boolean function that t..
Calculate the heat input to the gas : Consider the process AB is this TS diagram for 2 moles of SO3 with all degrees of freedom active. calculate the heat input to the gas
What will the cash flows for this project be : The firm has a tax rate of 35 percent, an opportunity cost of capital of 12 percent, and it expects net working capital to increase by $100,000 at the beginning of the project.
Design a combinational circuit that compares two numbers : Design a combinational circuit that compares two 4-bit numbers to check if they are equal. The circuit output is equal to 1 if the two numbers are equal and 0 otherwise.
Determine the maximum value for i and the time : The source-free circuit depricted in Fig. 9.1 is constructed using a 10mH inductor, a 1mF capacitor, and a 1.5k ohms resistor. a) Calculate alpha ( neperfrequency or exponential damping coefficient), omega-sub-delta (natural resonance frequency)
Find the mutual inductance of the two solenoids : A long solenoid of r =1cm and lnght l=1m is inserted into another long solenoid of radius r=3cm, Find the mutual inductance of the two solenoids
What is number of modes if waveguide with thickness is used : What is the largest thickness d of a planar symmetric dielectric waveguide with refractive indexes n_1=1.50 n_2=1.46 for which there is only on TE mode at lambda_0=1.3 micrometers. What is the number of modes if a waveguide with this thickness is ..
Research question and hypothesis : Use the library, Internet, and other available resources to develop a 6–8 page research proposal that includes the following:Introduction to your topic "Police Discretion" and related issues (variables)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find maximum reverse voltage that will appear across diode

It is required to use a peak rectifier to design a dc power supply that provides an average dc output voltage of 15 V on which a maximum of 1-V ripple is allowed. The rectifier feeds a load of 150 ohm.

  How does noise level change if cutoff frequency of filter

Consider the thermal noise produced by a resistor. How does the noise level change if the resistance is increased by a factor of 100 Next, assume the noise is passed through an ideal, noiseless low-pass filter.

  Find the current through the transmission line

The voltages at the generators buses are maintained at a magnitude of 1.0pu. The generator one (G1) is connected to bus 1. The generator two (G2) is connected to bus 2. The bus angle at bus 2 is taken as reference and is 00.

  Explain next generation transmission system

You are required to determine that this next generation transmission system will require a spectral efficiency of 5 bits/sec per Hertz.

  Determine the fundamental frequency and time period

Determine the fundamental frequency w0, the period t0, and the coefficients in the representation X(t) = x0 + Re{k=1N Xkejkwot} for the above input. Remember, you can do this problem without evaluating any integrals.

  Explain why norton equivalent circuit approximates sources

A 100 V power supply has a series limmitin restor of 100 k ohms connected to its output. draw the norton equivalent cirtuit for the power supply. explain why the norton equivalent circuit you drew approximates an ideal current source

  Define asynchronous and synchronous communication mode

What are the respective advantages and disadvantages of the asynchronous and synchronous communication modes from a reliability perspective?

  Calculate the triggering angle for the speed of 1000rpm

A 220 V, 1500 rpm, 11.6 A (armature current) separately excited motor is controlled by a single phase, full wave SCR converter. The armature resistance of the motor is 2 ohm. The ac source voltage is 230 V (rms) 60 Hz.

  Calculate the value of vl developed across

Calculate the value of vL developed across a 300 H coil when the instantaneous rate of change in component current equals 500 mA/s.

  What type of chemical reaction is taking place

1) What type of chemical reaction is taking place 2) How many liters of 0.100 M HCl would be required to react completely with 5.00 grams of calcium hydroxide 3) If I combined 15.0 grams of calcium hydroxide with 75.0 mL of 0.500 M HC..

  Find values of r and x and the supply voltage v

A load consists of a resistance R in parallel with a capacitor of reactance X. The load is fed from a single phase supply through a line of impedance 8.4 + j11.2 ohms. The rms voltage at the load terminal is 1200 at 0 degress V rms,

  Find the value of the lumped elements c and l

A.) We would like to use a series lumped element b to match this load. What is the length of the line where the normalized input impedance is z= 1-jb(d/\lambda). If the rfequency is 1GHz , find the value of the lumped element(C or L).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd