Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
design a circuit which accepts 2-bits input DUTY (‘01' for 12.5%, ‘10' for 25% and ‘11' for 37.5%). Assume 0% duty (all low) for input DUTY='00'. The circuit will need to be sequential and sensitive to a positive edge of another input CLK. Use the function generator or a de-bounced push button to provide CLK. Use another push button for the reset input RST. Connect the PWM output to an LED, for preliminary testing with slow clock frequency, then to the oscilloscope to show final results with multiple frequencies between 10 KHz to 1MHz. In the final demonstration, connect CLK to CH1, and PWM to CH2, and show both on the same screen of the oscilloscope. Attach sketches or images of the results in the report.
The instantaneous power p into a one port containing resistors and inductors has maximum value 100(1+sqrt2) W and minimum value 100(1-sqrt2)W. (note that instantaneous power is measured in W, and it contains various contributions
To develop contoller as a sequential circuit using minimum number of D flip-flops and the minimum number of external gates. the controller should set the values of the control lines appropriately to drive the combinational logic circuit.
If a single-loop circuit consists of an ideal 15-V dc source VS, a variable resistor R and the described Zener diode, find the range of values of R for which Zener diode remains in constant reverse breakdown with no danger of failure.
an fm transmitter delivers to a 50 ohm antenna a signal voltage of V(t)= 75sin(10^8 t+2 sin 10^3t) determine(a) carrier frequency (b) Intelligence frequency (c) modulation index (d) Total Power in FM signal
For input signal voltages between these limits, the input should pass unaltered to the output. The peak current drawn from the input source may not exceed 1mA. You may use any circuit component we've studied except opamps.
If V = 12sin( 2 pi 1800 + 45). What would you read on a DMM Would this voltage be for an inductor or capacitor What would be the frequency and phase What does the 12 stand for Explain.
By direct integration find the Laplace transforms and the region of convergence of the following functions
A communications channel has a bandwidth of 2,000 Hz and a signal-to noise-ratio (SNR) of 20 dB. What is the maximum possible data rate
A. Determine the fundamental frequency w0, the period t0, and the coefficients in the representation X(t) = x0 + Re{(sigma)k=1N Xkejkwot} for the above input. C. Now consider a new signal y(t) = x(t) + 10 cos (50 pi t - pi/6). How is the spectrum ..
F(a,b,c,d) = Σ m(7, 11, 12, 14) + Σ d(0, 10) (a) Find all of the prime implicants of F'. (b) Find a minimum product-of-sums for F. Note: F' is specified in (a) and F in (b).
Determine the transfer function for a first order low pass filter with a cutoff frequency of 1000 radians/sec (note radians and not Hertz) and a pass band gain of 1 using the following types.(a) Butterworth type(b) Chebyschev type
On a frictionless table, a glob of clay of mass 0.220 kg strikes a bar of mass 0.600 kg perpendicularly at a point 0.150 m from the center of the bar and sticks to it. If the bar is 1.380 m long and the clay is moving at 8.700 m/s before striking ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd