Design a circuit to control a network of switches

Assignment Help Electrical Engineering
Reference no: EM13256020

A circuit is required in order to control a network of switches. The circuit has four inputs: three of the switches are normal on/off switches while the fourth switch is an enable switch for the entire circuit. The circuit should have the following characteristics:

• If the enable switch is off, the single output will be LOW

• Otherwise, if any two (and only two) switches are one, then the output is HIGH

• Three switches will never be on simultaneously

• The circuit output is low under all other conditions

Reference no: EM13256020

Questions Cloud

The ph difference across the membrane of a glass electrode : The pH difference across the membrane of a glass electrode is 6.45. How much voltage is generated by the pH gradient at:25degreesC and 40 degreesC
Build lamp logic for a stationary bicycle exhibit at museum : As speed increases, the lower lamp, L1 lights, then L1 and L2, then, L1, L2, and L3, until all lamps light at the highest speed. Once all the lamps illuminate, no further increase in speed will have any effect on the display.
A chemical reaction is found to have an activation energy : A chemical reaction is found to have an activation energy (Ea = 15 kJ/mol). At a temperature of 505 K, what fraction of collisions have enough energy to exceed the activation energy
The volume of added acid required to reach the equivalence : Consider the titration of a 26.1 mL sample of 0.115 M RbOH with 0.110 M HCl. Determine each of the following.
Design a circuit to control a network of switches : A circuit is required in order to control a network of switches. The circuit has four inputs: three of the switches are normal on/off switches while the fourth switch is an enable switch for the entire circuit. The circuit should have the followin..
Find the value of the inductance : A series RCL circuit contains a 4.99-µF capacitor and a generator whose voltage is 11.6 V. At a resonant frequency of 1.20 kHz the power delivered to the circuit is 24.1 W. Find the value of the inductance
Why does the cost of equity increase with an increased : Why does the cost of equity increase with an increased use of debt in the capital structure?
Determine the emf of the solar cell : A solar cell generates a potential difference of 0.094 V when a 560 ? resistor is connected across it, and a potential difference of 0.14 V when a 1100 ? resistor is substituted. What are the emf of the solar cell
How many days are in the cash cycle : Harry Joiner, Inc. currently has an inventory turnover of 15.7, a payables turnover of 9.6, and a receivables turnover of 8.1. How many days are in the cash cycle?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Which parameter has the largest impact on the output voltage

If these nominal non--ideal parameters are replaced, one at a time, by A = 50000, Ri = 1 M and R0 = 150 (each of which is twice as bad as the nominal values), which parameter has the largest impact on the output voltage

  Write an expression for the voltage using a cosine function

a sinusoidal voltage has a peak value of 15V, a frequency of 500Hz, and crosses zero with a positive slope at t=0.1 ms. write an expression for the voltage using a cosine function in terms of t and constant pi.

  Determine what is the constant horizontal acceleration

Given an object with a mass of 55 lbm, who starts at rest but experiences a constant horiz. force due to resultant force applied for 10 seconds. The work of the resultant force is 7,782 lbf*ft.

  Calculate the pressure of co2 in state 3

A piston-cylinder device contains carbon dioxide CO2 (molar mass = 46 g/mol) as shown in the figure. The cross-section area of the piston is 0.25 m2 and the initial cylinder height is 50 cm. CO2 is initially at 40 bar and 500 oC (state 1).

  What is the magnitude of the instantaneous current

A charged 100-pf capacitor has initial voltage across it of 10V. a 100kohm resistor is suddenly connected across the capacitor (at t=0) to discharge it. What is the magnitude of the instantaneous current at 20 usec?

  Draw the complete circuit including the load

Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any circuit element we've studied. State the values of all circuit elements

  Explain the parking lot of the spenditall megamall

The parking lot of the Spenditall Megamall has an area of 128 ac. It is partially landscaped to provide some areas of grass. Assume that an average of 63% of the water that falls on the parking lot will flow

  Find the maximum torque on an orbiting charged particle

Find the maximum torque on an orbiting charged particle if the charge is 1.60E-19C, the circular path has a radius of 0.5E-10m, the angular velocity is 4E16 RAD/S, and B=0.4E-3T.

  Find the maximum allowable thermal resistance from junction

Find the heat energy generated by this amplifier. Assuming the BJT power transistor has a maximum junction temperature of 155 0C, if the ambient temperature is 25 0C, find the maximum allowable thermal resistance from the junction to ambient.

  Determine the value of the two items multiplied

Write a simple shell script called mathmagic that takes two arguments in at call time and returns to the stdout the value of the two items entered, the value of the two items added together, the value of the two items subtracted

  Consider a three-phase distribution feeder

Consider a three-phase distribution feeder with line reactance of10 ohm supplying a three-phase Y-connected load of 200 kVA at power factor of 0.85 lagging.

  Determine the capacitance of a parallel-plate capacitor

determine the capacitance of a parallel-plate capacitor having plates 14cm by 30cm separated by 0.01mm. The dielectric has (epsilon)(r)=15

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd