Design a circuit that takes output from each of microphones

Assignment Help Electrical Engineering
Reference no: EM13261660

You have formed a band despite advice to the contrary. Actualy the band is pretty good except for the fact the lead singer (who owns the the drum set the microphones and the garage where you practice) is a bit tone deaf. Design a circuit that takes the output from each of the five microphones your band uses and adds the voltage to create a single voltage signal which is fed to the amplifer. Except not all voltages should be equaly amplified. One microphone output should be attenuated such that its peak voltage is 10% of any other microphone's peak voltage.

Reference no: EM13261660

Questions Cloud

Evaluate the ph at the equivalence point in titrating : Calculate the pH at the equivalence point in titrating 0.100 M solutions of each of the following with 7.0X10^-2 M NaOH. (a) hydrobromic acid (HBr)
Find relative probability of finding electron at a distance : Determine the relative probability of finding the electron at the distance (a) 12 A beyond the barrier, and (b) 48 A beyond the barrier, compared to the probability of finding the incident particle at the barriers edge. Plot the wave function for ..
Compute the concentration of an aqueous solution : Calculate the concentration of an aqueous solution of Ca(OH2)that has a pH of 12.57? Express your answer using two significant figures.
Compute the concentration of an aqueous solution : Calculate the concentration of an aqueous solution of Ca(OH2)that has a pH of 12.57? Express your answer using two significant figures.
Design a circuit that takes output from each of microphones : Design a circuit that takes the output from each of the five microphones your band uses and adds the voltage to create a single voltage signal which is fed to the amplifer. Except not all voltages should be equaly amplified.
Compute delta g rxn at 25 c for the process agi : The solubility product constant at 25 C for AgI(s) in water has the value 8.3x 10-17. Calculate Delta G rxn at 25 C for the process AgI (s) --> Ag+ (aq) + I- (aq) where (Ag+)= 9.1 x 10 -9 and (I) = 9.1x10-9
What is the half-life of the material : In 6.00 days the number of radioactive nuclei decreases to one-eight the number present initially. What is the half-life (in days) of the material
Calculate value for average voltage for three input signals : Design a circuit that will calculate the value for the average voltage for three input signals. Draw the circuit schematic identifying supply voltages and show your work on component selection.
Draw layout design for mos inverter using depletion-type fet : Create the layout design for MOS inverter using a depletion-type transistor with VTL = -0.3V and an enhancement-type device with VTO = 0.5V such that tPLH is less than or equal to 15ns and tPHL is less than or equal to 1ns

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the effective voltage if the waveform is sinusoidal

Calculate The Average voltage generated in 6 turn full pitch coil of a 25 cycle alternator if the flux per pole is 7.2 x 10^5 maxwells. What is the effective voltage if the waveform is sinusoidal.

  Explain what rf bandwidth must the radio link provide

What RF bandwidth must the radio link provide if the modulation is binary phase shift keying (BPSK)?

  What is the value of the total circuit complex impedance

An input signal of 10V at 0degrees and a frequency of 1592Hz is applied to a series RLC circuit with resistor R=100ohm, inductor L= 40mH, and a capacitor C=0.5uF. The value of the total circuit complex impedance is

  Find the total real and reactive power delivered to load

A 345-kV, 3-phase transmission line delivers 100 MVA, 0.866 lagging, to a wye connected load. Calculate the following: a. The total real and reactive power delivered to the load. b. The real and reactive power per phase.

  Determine the time required to obtain the desired thickness

A thermal oxide of thickness 120 nm needs to be grown on a silicon wafer (100) in dry oxygen. If the process integration issue requires having a temperature not higher than 1050 degreeC, determine the time required to obtain the desired thickness.

  Write down the principle of energy conversion

Write down the principle of energy conversion and give an example for single and double excited system.

  Find the applied voltage of an iron-core transformer

Find the applied voltage of an iron-core transformer if the secondary voltage is 240 v, and Np = 60 with Ns = 720

  How to build cicuit that must be able to operate 3 amp load

build a cicuit that must be able to operate a 3 amp load of the LED while being able to operate at voltages around 3V or 6V. It must be able to keep the LED on constantly while also being able to pulse the LED.

  Find the probability that screws drawn will be nondefective

Three screws are drawn at random from a lot of 100 screws, 10 of which are defective. Find the probability that the screws drawn will be nondefective in drawing (a) with replacement, (b) without replacement.

  Determine the value of the resistance in terms of parameters

Show that a linear dependent current source controlled by a voltage appearing across an element in parallel with the dependent source is equivalent to a resistor. Determine the value of the resistance in terms of the parameters of the dependent so..

  Find the output by taking the inverse laplace transform

1. Find the transfer function 2. Find the Laplace transformation of the output when x(t)=sin(t)u(t) 3.Find the output by taking the inverse Laplace transform of part 2.

  Why being barefoot act lead to hazardous safety conditions

Explain why the following act lead to hazardous safety conditions when working with electrical equipment. (a) wearing metal rings or bracelets (b) being barefoot,(c) working on damp or concrete floor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd