Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design a 3-stageMOSFET amplifier that provides a differential gain |vo/vd| > 20V/V, a small common-mode gain, and an output resistance Ro >1kΩ. The amplifier is to drive a load RL = 10kΩ. The frequency of the signal source is 10 kHz. Power supplies with±8 V are available. Assume that the output resistance ro ofall MOSFETs are very large and can be neglected. Also, assume thatK=0.5 mA/V2 and Vt = 1.5 V for all MOSFETs. Note that the designswill vary between individuals and there is not a single correctdesign. It is important that all the requirements listed above are satisfied.
A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.
Design and build your traffic light. Include Truth tables, state diagrams, state tables, and counter design. You will burn an EPROM during lab to supply the outputs of your system; however, make sure your counter and walk signal circuit is complet..
A lossless line having an air dielectric has a characteristic impedance of 100 Ohms. Another line that is identical in dimensions to the air line is fabricated with the air displaced by a dielectric material have an \(\epsilon_{r}\) value of 4.
A 60-Hz, 765-KV three-phase overhead transmission line has four ACSR 900 kcmil 54/3 conductors per phase. Determine the 60-Hz resistance of this line in ohms per kilometer per phase at 50 degrees Celsius.
1) Ohm's. Law is considered one of the key foundation in electronics . Why (2) Why do we have to build and test circuits when we have simulation tools
Discuss how you can identify which resistances are in series and which ones are in parallel in a series-parallel circuit. How might this affect how you measure current and voltages in the circuit with a digital multimeter.
First, generate an array of 20 input random integers in the range between 0 to 30 and display. Then, sort the generated 20 random integer numbers in ascending order using "THE SELECTION SORT" method and display your sorted output data flow chart.
An analog signal xa(t), band-limited to 5 Hz, is sampled at a rate of 10 samples per second to give a discrete-time signal x(n) = xa(0.1n). The discrete-time signal x(n) is then filtered with an digital FIR filter, h.
Be sure to specify three things for each component: its digital frequency (a number between 0 and 0.5), its amplitude (in digital numbers, peak-to-peak), and its phase relative to the original analog signal (either 0 degrees or 180 degrees).
Consider a continuos time LTI system with step response given by ys(t) = tu(t) - (t - 2)u(t-2). Determine the output y(t) if the input to the system is given by x(t) = u(t) - u(t - 2) using complex domain (not time domain) analysis techniques.
What are the differences between volatile and nonvolatile memory What are advantages and disadvantages of volatile and nonvolatile memories
Your will simulate 10lottery drawings. Store those data to a 3 10 array. The rowsindicate the three balls in a lottery drawing. The columns indicatethe 10 times drawings.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd