Describe the complete circuit details of dip switch

Assignment Help Electrical Engineering

Reference no: EM13230552

A fully 16-bit external data bus 68000-microprocessor is used in the following motor control and instrumentation system. It operates as follows:

1. An operator prepares an 8-bit binary value with a dip switch.

2. A momentary contact switch (single-pole-single throw) connected to only one end of a cross-coupled NAND latch is activated. This sets the output of the latch to a logic one.

3. All this time, the 68000 has been polling the output of the latch.

4. When microprocessor detects a logic one at the output of the latch, it resets the latch to a logic zero by sending a low going pulse to the other input leg of the latch.

5. The microprocessor then reads the 8-bit data from the dip switch and puts the value in memory starting at location called ‘BUFFER' . This same data is sent to a digital-to-analog converter ( D/A) whose output drives a dc motor.

6. The output of the dc motor is connected to a tachometer , whose output is, in turn, connected to an 8-bit microprocessor compatible analog-to-digital converter (A/D). The A/D is connected in a free running configuration.

7. The 68000 reads the A/D output, compares it with the original data from the dip switch, sends the hexadecimal number ‘$42' to an 8-bit LED pack if the compared values are different, and sends the hex. value ‘$99' to the same 8-bit LED pack if the compared values are equal.

8. Finally, a centronics parallel printer port is polled for a low-true printer ready logic signal, and the A/D data is sent to the printer. A. Provide a hardware design for the system. Partial and simplified decoding is acceptable. Use only the following four addresses for your ports design: $3001 ; $30F1; $30E1; $31F1. Do NOT include interface to memory modules and reset circuits. Design the address decoders, I/O ports (where needed), DTACK circuitry, complete circuit details of dip switch and other switch interconnections, complete circuit details of LED interconnections, input/output ports with appropriate handshaking signals. Clearly label A/D, Printer, D/A signals showing how they connect to other circuits. B. Provide a well-commented 68000 assembly language program to accomplish the tasks indicated in items 1 thru. 8. Clearly identify the specific polling routines and input/output control software for each input/output device

Reference no: EM13230552

Questions Cloud

What are the upper and lower control chart limits : The defect rate for a product has historically been about 2.4%. What are the upper and lower control chart limits for a p-chart, if you wish to use a sample size of 100 and 3-sigma limits?

Determine what steps you would take to initiate the project : Determine what steps you would take to initiate the project and include how your leadership style would predict your action.

Minimize behavioral resistance to change : The main goal of your proposal is to minimize behavioral resistance to change at both companies,to include clients, leadership, and subordinates.

State what molarity of aqueous magnesium chloride solution : What molarity of aqueous magnesium chloride solution can be expected to show the same conductivity as 0.0075 M aluminum sulfate at 15,000 units.

Describe the complete circuit details of dip switch : The microprocessor then reads the 8-bit data from the dip switch and puts the value in memory starting at location called ‘BUFFER' . This same data is sent to a digital-to-analog converter ( D/A) whose output drives a dc motor.

Explain what is the solubility of oxygen in air : In 1.00 atm of pure oxygen, the solubility of O2(g) in water is 1.26 x 10^-3 M at 25.0 degree C. The mole fraction of oxygen in air is 0.210. If the atmospheric pressure is 0.979 atm, what is the solubility of oxygen in air at 25.0 degree C?

Discribe atomic mass and carbon atoms : The molecular weight of a compound is the sum of the atomic mass of its atoms. Compound X has a molecular weight of 522 daltons and is known to consist of equal numbers of C, O, and H atoms

What are three ways in which corporations can demonstrate : What are three ways in which corporations can demonstrate a sense of social responsibility?

Compute the change in ph : Calculate the change in ph when 6 ml of 0.1 M HCl is added to 100 ml of a buffer solution that is 0.1 M in NH3 and 0.1 M in NH4Cl.

User Account

All Pages