Derive the expression for a simple spring mass system

Assignment Help Mechanical Engineering
Reference no: EM13709782

1. Derive the expression for a simple spring mass system equation and its response. Plot the response for 3 different values of k, (k=1, k=10, k=100) assume mass M= 1, what are the natural frequencies in rad/sec and Hz for each case.

 

2. Explain the difference between 0 order, 1 order and 2 order system with figures and examples.

Reference no: EM13709782

Questions Cloud

Hacking into harvard : Hacking into Harvard, located here or on page 71 in your textbook. As applicants began to defend themselves against the penalties handed out by the business schools, they appealed to both consequentialist and nonconsequentialist criteria to sup..
Find the electric potential energy of the electron : Two stationary point charges of 5.00nC and 2.00nC are separated by a distance of 50.0cm. What is the electric potential energy of the electron
Radius of the earth : A 1.0 litre bottle of water weighs 9.79 N at sea level. If the bottle was taken to the top of Mt Everest (8848 m above sea level), how much would it weight there? Take g at sea level to be 9.81 m/s2 and the radius of the Earth to be 6371 km.
Where would the net electric field be zero : Two particles having charges of 0.550nC and 4.95nC are separated by a distance of 1.90m. Where would the net electric field be zero
Derive the expression for a simple spring mass system : Derive the expression for a simple spring mass system equation and its response. Plot the response for 3 different values of k, (k=1, k=10, k=100) assume mass M= 1, what are the natural frequencies in rad/sec and Hz for each case. Explain the differe..
Find the speed of transverse waves in the wire : A variable-length air column is placed just below a vibrating wire that is fixed at the both ends. Find the speed of transverse waves in the wire
Find the total force resisting the motion of the block : A 25-N block slides down a plane inclined at 21.2 degrees to the horizontal with constant velocity. Find the total force resisting the motion of the block
Car accelerates from rest along a straight section of road : A car accelerates from rest along a straight section of road. It starts at position s = 150 m and reaches a speed of 20 m/s at position s = 200 m. It is proposed that this acceleration, a, can be modelled as being a function of position, s, in the fo..
Ball is dropped inside an evacuated tube : A ball is dropped inside an evacuated tube so that there is no aerodynamic drag acting on the ball. At one point it is at a height of 2.5 m and is dropping at a speed of 1.0 m/s. What will be the height of the ball when its speed is 5.0 m/s? Take g= ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Te velocity of point p relative to frame a is vpa -149 i

the velocity of point p relative to frame a is vpa -14.9 i 19.4 j fts and the acceleration of p relative to frame b

  At the bottom with a height of 05 m is liquid water on top

a 2.5 m tall steel cylinder has a cross sectional area of 1.5 m2 . at the bottom with a height of 0.5 m is liquid water

  How far below the liquid level in the tank must the pump be

a feed rate of 200gpm of a hydrocarbon mixture at 70c is being pumped from tank at 1 atm abs pressure to a distillation

  Some of the flow exits at an intermediate pressure at 2 as

argon gas flows steadily through a well-insulated turbine at the conditions shown below. some of the flow exits at an

  Methane gas in piston-cylinder assembly goes under adiabatic

Methane gas in a piston-cylinder assembly goes under an adiabatic (no heat transfer) quasi- equilibrium compression. (This process is called isentropic process). The pressure and volume of the gas during the process are related as PV 1.3=constant.

  Dtermine the final volume v2 of the gas pv constant p1

a gas contained in a piston cylinder assembly undergoes a process from state 1 to state 2 defined by the following

  Assuming you have a thermometer and a device to measure

assuming you have a thermometer and a device to measure the speed of sound in a gas explain how you can determine the

  Which of the following polymers should you select for this

1. a 1000 mm long x 100 mm wide x 4 mm thick polymer plate is designed to carry a tensile load 4 kn. in the past a

  Suppose that the mass in a mass-spring-dashpot system with

suppose that the mass in a mass-spring-dashpot system with m10 c9 and k2 is set in motion with x00 and x05 a find the

  The relationship between pressure and volume during the

a gas expands from an initial state where p1 500 kpa and v1 0.1 m3 to a final state where p2 100 kpa. the relationship

  The valve is opened and the two tanks eventually come to a

two heavily insulated tanks are connected by a valve. tank a has a volume of 600l and contains water at 200kpa and

  Assuming the wheels do not slip on the ground determine the

the jeep has a weight of 2510lb and an engine which transmits a power of 100 hp to all the wheels. assuming the wheels

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd