Derive an expression similar to using this approach

Assignment Help Mechanical Engineering
Reference no: EM131198023

Consider (15.2-32). Another approach that has been suggested [2] for this width is such that the reciprocal of wsiR is set to the average of the reciprocals of the chord lengths between inner corners of slot at the top of the slot (under the tooth tip) and the outer corners of the slot at the bottom of the tooth. Derive an expression similar to (15.2-32) using this approach.

1121_0afb1ea0-c3b5-421d-b19b-8ed0a59bae53.png

Reference no: EM131198023

Questions Cloud

Proportional income tax rate : Whal will the equilibrium level of income Y be? (Hint: Round off the answer in question 19 to two digits after the decimal to obtain the answer for question 3.20.)
Describe the implications of each alternative action : Discuss alternative courses of action that could be taken by the counselor to rectify each dilemma. Describe the implications of each alternative action; lay out the limitations and advantages of each alternative considered.
Economic theory have to say about these career choices : Kat Von D, also known as Katherine von Drachenberg, is an American tattoo artist, model, musician, entrepreneur, and television personality. She is best known for her work as a tattoo artist on the TLC reality television show LA Ink. What most people..
Problem regarding the consumption function : Given a consumption function C = 1 000 + 0,4Y with a proportional income tax rate of 40%, what is the multiplier? Round off your answer to two digits after the decimal.
Derive an expression similar to using this approach : Derive an expression similar to (15.2-32) using this approach.
What are the tax implications attributable to these sales : Rebecca sells a painting for $1,200 that she acquired five years ago for $900. What are the tax implications attributable to these sales?
Marine transaction and commercial : Enumerate the common areas where frauds and disputes normally take place in internationally marine transaction and commercial shipping , and state the common precautions to be taken by international buyer and sellers to prevent the possibilities o..
What is a black swan event : 1. What is a Black Swan event? 2. Does it ever make sense a priori to devote resources to preventing a black swan event? Explain. 3. Does it ever make sense a priori to devote resources to containing a black swan event should one occur? Explain.
At that reserve price what is the expected profit : What is the best reserve price?- At that reserve price, what is the expected profit? - At that reserve price, what is the standard deviation of profit?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the composition in atom percent

What is the composition, in atom percent, of an alloy that consists of 5.5 wt% Pb and 94.5 wt% Sn?

  What is the velocity of water at the nozzle outlet assume

a fire hose has a length of 100 feet is 4 inches in diameter and has a roughness of 14inch. the fire hose leads into a

  The initial density of air in the tank is 002 slugft3 the

air enters a tank through an area of 0.2 ft2 with a velocity of 15 fts and a density of 0.03 slugft3. air leaves with a

  How far up the ramp will the spring send the crate

A crate of mass 10kg is placed on a ramp elevated at 30 degrees from the horizontal. The ramp is 2m long. The coefficient of static friction is .4 and coefficient of kinetic friction is .3. At the low end of the ramp and oriented parallel to it is a ..

  What is the heat transfer to the plate

Explain why the gas's pressure will affect the heat transfer to the coolant - What is the heat transfer to the plate if the plate

  What is the maximum normal strain e at the top and bottom

What is the maximum normal strain ε at the top and bottom of the bar?

  Principles of dimensional metrology

Balls of diameters 25 mm and 20 mm were used to measure a taper ring gage.  The large ball protruded mm above the end face of ring gear while the distance of the end face from the top of the 20 mm diameter ball was 40 mm.

  Saturated vapor at 400 kia flowing in a line is taken out

saturated vapor at 400 kia flowing in a line is taken out through a valve to 100 kpa. what is the temperature in c as

  Determine the heat transferred to and the work produced

Steam at 75 kPa and 13 percent quality is contained in a spring-loaded piston-cylinder device, as shown in the figure, with an initial volume of 5.28 m^3. Steam is now heated until its volume is 13.20 m^3 and its pressure is 300 kPa. Determine the he..

  What is the effectiveness of the heat exchanger

A concentric tube, i.e. tube-in-tube, heat exchanger uses water at 15 °C to cool ethylene glycol from 100 °C to 60 °C. The water and glycol flow rates are each 0.5 kg/s. The specific heat of glycol and water are 2637 J/kg-K and 4180 J/kg-K, respectiv..

  Material index for a torsion bar with solid circular section

Derive the material index for a torsion bar with a solid circular section. The length L and the stiffness S* are specified, and the torsion bar is to be as light as possible. Follow the steps used in the text for the beam, but replace the bending sti..

  Consider the power system as designed below the duty fluid

consider the power system as designed below. the duty fluid is water and has a mass flow 0.75 kg s and all piping

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd