Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
our boss asks you to contruct a temperature sensorfor measuring the ambient temp outside (-30degreee celcius<= T<= 40 deg. c). You decide to base operation on the change inresistance accociated with a bar shaped piece of SI.(a) indicate doping and dimensions of your sensor(b) derive an expression for the sensitivity (dR/dT inΩ/deg celcius) of sensor over operating temp range. Is it preferable to use low or high dopings? explain.(c) What are the upper and lower temp limits of op(approx)?explain.(d) Plot R vs. T of sensor over required temp range ofoperation.
Write a script that numerically calculates the slopes for the function y = ex. Use x-values that range from 0 to 10 in increments of 0.1. Using these slopes, calculate the equation of a line that is tangent to the function at x = 8.3.
A hot-air balloon is rising upward with a constant speed of 3.86 m/s. When the balloon is 9.27 m above the ground, the balloonist accidentally drops a compass over the side of the balloon. How much time elapses before the compass hits the ground
A) the required step-up voltage ratio for satisfactory performance. B) the voltage ratio of a standard buck-boost transformer that most closely meets the requirements of the load. C) the voltage at the load with the buck-boost transformer installed.
Ziegler-Nichols Open Loop Tuning Often, when working with a faster loop, many people will opt only for a PI control philosophy
An input signal of 10V at 0degrees and a frequency of 1592Hz is applied to a series RLC circuit with resistor R=100ohm, inductor L= 40mH, and a capacitor C=0.5uF. The value of the total circuit complex impedance is
Determine the capacitance required in a half wave rectifier to produce a ripple voltage less than 0.2V. Assume that the input is a 60Hz signal with maximum voltage VM=100V
Suppose we have a circuit in which a current source of 5 amperes is connected to 3 resistances in parallel.If you need to calculate voltage difference across current source EXPLAIN USING KCL why is that the digital multimeter should have infinite ..
AnNMOS operating in triode region with Vds=0.1V conducts 60μA forVgs=2V. The device conducts 160μA for Vgs=4V. Calculate Vt. IfKn'=25μA/V2 , what is the device W/L What current would flow for Vgs=3V and Vds=0.15V
A three-phase, 345-kV, 60-Hz transposed line is composed of two ACSR 1,113,000, 45/7 Bluejay conductors per phase with flat horizontal spacing of 11 m. The conductors have a diameter of 3.195 cm and a GMR of 1.268 cm.
Suppose you have a 2 kW electric heater rated for 220 volt operation, which you intend to operate at a reduced power dissipation of 1kW. Calculate the proper amount of voltage you would need to achieve this reduced power dissipation
A silicon sample is 2.5 mm in length, 1.2 mm in width and 0.7 mm high. It has been doped with Boron with a doping density of 8.5 x 1016 cm-3. Assume the temperature is 300°K.
The following equation represents the complete combustion of ethane: 2C2H6(g) + 7O2(g) 4CO2(g) + 6H2O(g)At the same temperature and pressure what is the maximum volume in liters of carbon dioxide
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd