Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. At resonance, a series RLC circuit will be:
2. definition of characteristic impedance?
3. When moving from the source to load, current and voltage traveling waves move:
4. If a receiver is under-selective:
5. An AM signal having a carrier frequency of 560 kHz is to be mixed with a local oscillator signal at a frequency of 1035 kHz. What does the output of the IF amplifier consist of?
6. The AGC control voltage:
A touch sensor base on a piezoresistor built into a micromechanical cantilever made of silicon is cnnected in a Wheatstone-bridge configureation with a Vo = 1 volt. If L = 1.44cm and W = 1 cm
Consider the following second order transfer function: G(s) = 2/s2+0.4s+1.. Use MATLAB Simulink software to investigate the performance of APD controller with a fixed proportional gain of Kp=0.2. Demonstrate the effect of changing the value of Kd ..
In the presentation, "IT and Smart Grid" the presenter, Dr. Peter Will, provided several definitions of "smart-grid". Provide your definition of smart-grid the way you understand it. What are some of the benefits of "smart grid" application
Design and simulate a power supply that takes line voltage and produces a 15V output with less than .5% ripple voltage. For your design, provide all the data sheets, calculations and simulations for the output characteristic
In a matched CMOS inverter in which Vtn = - Vtp = 0.5 V, VDD = 1.8 V, kn = kp = 600 uA/V^2 and fabricated in a 0.13 um technology, use the average current method to determine W/L ratios such that the propagation delay tp is smaller
the arrival rat of cars at a toll plaza is 50 cars per hours. There are three boothes serving an a verage of 20 cars per hour. Assume an exponential for service time and a poisson distribution for arrival time.
At 0°C the circuit is balanced and at this temperature the RTD has a resistance of 200 W. Determine the change in output voltage for a 1°C change in temperature now assuming the meter has an internal impedance of 8,000 W.
A 230kVA, 2300/230V, 60 Hz, step-down transformer has the following parameters. RH =1.2-ohm, XH =3-ohm, RL =12m-ohm, XL =30m-ohm, Rh+c=2k-ohm, , Xm =1.8k-ohm. If the transformer operates at half load with unity power factor
A dielectric slab with 500mm x 500mm cross-section is 0.4m long. The slab is subjected to a uniform electric field of E = 6ax + 8aykV /mm . The relative permittivity of the dielectric material is equal to 2. The value of constant ε0 is8.85 × 10-12F /..
For a 32 bit CMOS 5 volt microprocessor that has a 32 bit address bus and a separate 32 bit data bus, and the processor has a 1 nS rise time and 0.5 nH of ground inductance on a board made from glass epoxy material.
Design an air-filled C-band (5-8 GHz) rectangular waveguide such that the center frequency of this band (f= 6 GHz) is at least 25% higher than the cutoff frequency of the TE10 mode and at least 25% lower than the cutoff frequency of the next highe..
Consider the second-order band pass filter shown in Figure. Derive expressions for L and C in terms of the resonant frequency ω0 and quality factor Qs.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd