Define the problem on rankine cycle

Assignment Help Electrical Engineering
Reference no: EM13141719

Water is the working fluid in a vapor power cycle with reheat, superheat and reheat.

Superheated steam enters the first turbine stage at 8 MPa, 480 C and expands to 0.7 MPa. It then is reheated to 480 C before entering the second turbine stage, where it expands to the condenser pressure of 8 KPa. The mass flow rate of steam entering the first turbine stage is 2.63*10^5 Kg/h. Each turbine stage operates with an isentropic efficiency of 58%. The pump operates with an efficiency of 80%.

Determine the net power developed, the cycle thermal efficiency and the rate of heat transfer to the cooling water passing through the condenser.

Reference no: EM13141719

Questions Cloud

Explain dissipations of power in lightbulbs : Dissipations of Power in Lightbulbs, An incandescent lightbulb rated at 100 W will dissipate 100 W as heat and light when connected across a 110-V ideal voltage source
Find probability that sample will have between a range : Conduct a marketing experiment in which students are to taste 1 of 2 different soft drinks. What is the probability that the sample will have between 50% and 60% of the identificaton
Discuss what might have caused these variances : determine the rate variance, time variance, and total direct labor cost variance. discuss what might have caused these variances.
Discuss the advantages and disadvantages of diffusion : With regard to bringing solutes into the cell across the plasma membrane, discuss the advantages and disadvantages of diffusion, facilitated diffusion, active transport, and endocytosis.
Define the problem on rankine cycle : Water is the working fluid in a vapor power cycle with reheat, superheat and reheat. Superheated steam enters the first turbine stage at 8 MPa, 480 C and expands to 0.7 MPa
What would be the pressure : suppose a can contains gas at a pressure of 755 mm Hg and a temperature of 25 degrees celsius, what would be the pressure if the can was heated to 1155 degrees celsius ?
Ias3/aasb 3 business combinations : IAS3/AASB 3 Business Combinations IAS116/AASB116 Property, plant and equipment IAS138/AASB138 Intangible assets
What figures constitute this balance : Benns adopts the equity method for its 100 percent investment in Water. At the end of six years, Benns reports an investment in Waters of $920,000. What figures constitute this balance?
What would happen to plant growth during long summer drought : In moist temperate environments like New England, most plants are C3 plants. Describe what would happen to plant growth during a long summer drought in Central Massachusetts ?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Function of the hmi in a scada system

This assignment contains electronics engineering questions like State the commonly found components of a SCADA (Supervisory control and data acquisition) system. and decribe the function of the HMI in a SCADA system.

  Explain eigenfunctions and lti systems

Eigenfunctions and LTI systems, The eigenfunction property is only valid for LTI systems. Consider the cases of nonlinear and of time varying systems.

  Design a device that remotely control at least two actuators

The purpose of this project is to design a device that would remotely control (from a Bluetooth-enabled mobile phone for instance) at least two actuators (e.g. relays and switches).

  Control systems- operation of a pid

Control Systems: Operation of a PID, Which one of the following statement regarding to operation of a PID is true?

  Explain basics problems of induction motor

Basics problems of Induction motor, The frequency of the induced rotor currents in the rotor of a 60 Hz induction, machine is 2 Hz. Furthermore, the fields in the air gap turn at -40 rpm with respect to the rotor.

  Define nmos fet and bjt analysis

A standard silicon NPN BJT is to be used as an amplifier. The emitter voltage is biased at 4 volts, the base is biased at 5 volts, and the collector is biased at 10 volts. Will this circuit perform as desired? Why or why not.

  Explain in detail on the fabrication process of the finfet

Explain in detail on the fabrication process of the FINFET. You must show a 3-dimensional view of FINFET and label the its L and W, the length and width of the gate.

  Explain what rf bandwidth must the radio link provide

What RF bandwidth must the radio link provide if the modulation is binary phase shift keying (BPSK)?

  Define what is the fm improvement in db

What is the peak frequency deviation of the FM signal? What is the FM improvement in dB?

  Plot the swing curve for the machine

Calculate the critical clearing angle and plot the swing curve for the machine - What is the power angle at the end of the 10 cycles?

  Define the winding resistance and leakage reactance

A 415V to 11 kV transformer has a rating of 200 kVA. The winding resistance and leakage reactance when referred to the primary are 0.014 and 0.057 ohms respectively.

  Explain what is the impedance of the load

A load has a 20 ohm resistor and a 4 Henry inductor connected in series. It is connected to a power source with v(t) = 100 cos(50t), connected in series to the load. What is the impedance of the load? Use phasor transform methods to obtain your an..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd