Create a message signal and a carrier signal

Assignment Help Electrical Engineering

Reference no: EM13539684

Use MATLAB environment to create a message signal and a carrier signal and apply a simplified amplitude modulation (DSB-SC-AM) to see the modulated signal in time domain. Later using the Fourier transform you will see how modulation affects the signal in the frequency domain.

To do this analysis, in the time domain:

1. Create a 1 second long message signal. The message signal is a rectangular pulse between 450 and 550 milliseconds with magnitude 1. (Hint: Create the signal using millisecond units ((t=0:0:001:1));

2. Create carrier signal of the same duration with frequency f0 = 400 Hz. You can either use sin or cos waveforms as a carrier with magnitude 1. (i.e. C = cos(2πf0t))

3. Modulate signal by multiplying the message signal and the carrier. Plot all 3 signals in the time domain and explain what you observe in the modulated signal.

In the frequency domain:

4. Take the Fourier transform of the message and carrier and modulated signal and plot the magnitude spectrum of all of the 3 signals. (Hint: Use fft, fftshift, abs, plot and other commands for his part; Apply 1000-point fft for clear results. To understand this better look up information on fft command by typing help fft in the command window).

5. Explain what you see in the spectrum of the modulated signal and how it relates to the spectrum of the message and carrier.

6. Solve this modulation problem by hand (i.e. take the Fourier transform of the modulate signal)

7. Plot the magnitude spectrum of the modulated signal as you computed by hand in part 6.

8. What are the similarities between your hand computed result vs. the MATLAB result from part 4?

9. What are the differences between your hand computed result vs. the MATLAB result from part 4? What causes these differences?

10. In MATLAB, show that by modulation we can have more than one user on the spectrum. For this you can create another message and put in on the different carrier and show that the spectrum of the 2 massage signals do not interfere. Explain how the receiver should be designed.

Reference no: EM13539684

Questions Cloud

How much energy must be added to the water by heating : The water is initially at room temperature (293 K). Water boils at 373 K. How much energy must be added to the water by heating it in order for it to start boiling?

The needs of the patient with the food intake issue : The RN can implement to address the needs of the patient with the food intake issue.

Determine cost of electricity consumed by this air-condition : Air is flowing steadily through a cooling section where it is cooled from 30 °C to 15 °C at a rate of 0.25 kg/s. If the average COP of the air-conditioner is 2.8 and the unit cost of electricity is 7 cents per kWh. Determine the cost of electricity c..

Find the mmoent of inertia of the pulley about its rotation : A textbook of mass 2.10 rests on a frictionless, horizontal surface. A cord attached to the book passes over a pulley whose diameter is 0.180 , to a hanging book with mass 2.92. find the mmoent of inertia of the pulley about its rotation axis

Create a message signal and a carrier signal : Create a message signal and a carrier signal and apply a simplified amplitude modulation (DSB-SC-AM) to see the modulated signal in time domain.

Calculate the maximum speed the automobile can have : Consider a wet banked roadway, where there is a coefficient of static friction of 0.30 and a coefficient of kinetic friction of 0.25 between the tires and the roadway. what is the maximum speed the automobile can have before sliding up the banking

What is the voltage across each capacitor : Three capacitors C1 = 2.5 µF, C2 = 7.5 µF, and C3 = 13 µF are connected as shown with a battery of voltage V = 18 V. (When entering units, use micro for the metric system prefix µ.) (a) What is the equivalent capacitance of this circuit? (b) What is ..

What is the equivalent resistance of this setup : A 10 ohm resistor and a 20 ohm resistor are connected in parallel. What is the equivalent resistance of this setup

How is research important in preventing disease : How is research important in preventing disease and/or the spread of disease? Give an example of how research has helped improve the outcomes of people with certain diseases. Also, explain how scientists determine if research sources and/or da..

User Account

All Pages