User Account

All Pages

Could this capacitor actually be constructed

Assignment Help Mechanical Engineering
Reference no: EM13961154

You have two flat metal plates, each of area 1.00 m^2, with which to construct a parallel-plate capacitor.

(a) If the capacitor of the device is to be 1.00 F, what must be the separation between the plates?

(b) Could this capacitor actually be constructed?

Please review my solution below and correct me where I am may be wrong, explaining any concepts I may be misunderstanding.

(a) The formula to calculate Capacitance is

C = ε0A / d
C = 1.00 F
ε0 = 8.85 pF/m
A = 1.00 m^2
d = ε0A / C

d = (8.85 μF/m)(1.00 m^2) / 1.00 F
d = 8.9 μm or 8.9 x 10^-12 m

(b) This is a very small distance and we know the smaller the distance the larger the capacitance. A 1 F capacitor is extremely large and probably would not be cost effective for the size to the materials needed.

Reference no: EM13961154

Questions Cloud

In what situations might each strategy be most effective : What ethical considerations that might surface if a major shareholder of a targeted acquisition is also the CEO and a Board member of the target?
Handling a small chain of upscale furniture outlets : You are the media planner for an agency handling a small chain of upscale furniture outlets in a top-50 market that concentrates most of its advertising in the Sunday supplement of the local newspaper. What would be your recommendation to the furnitu..
Calculate the work required to pull the material out of gap : Calculate the force of electrical attraction when the material is in the center of the capacitor
Describe a bowl opening to the right with a vertex : Describe it in words. A bowl opening to the left with a vertex at (2, 0, 0). A bowl opening to the right with a vertex at ( - 2, 0, 0). A bowl opening upwards with a vertex at (0, 0, 2).
Could this capacitor actually be constructed : If the capacitor of the device is to be 1.00 F, what must be the separation between the plates?
Determine the vector expressions for the velocity : The circular disk rotates with a constant angular velocity w=40 rads/sec about its axis which is inclined in the Y-Z plane at the angle A = arctan ¾. Determine the vector expressions for the velocity and acceleration for point P located on the r..
How you can classically condition a specific behavior : Give two examples of classical conditioning you have witnessed. Identify the neutral stimulus, the unconditioned stimulus, the unconditioned response, the conditioned stimulus, and the conditioned response. Develop a plan on how you can classicall..
Determine the relevant costs for the expansion decision : From the scenario for Katrina's Candies, determine the relevant costs for the expansion decision, and distinguish between the short run and the long run costs.
Calculate the dielectric constant of the material. : Determine the magnitude of the charge induced on each dielectric surface.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A rectangular gate of 1m wide is hinged at its top edge

a rectangular gate of 1m wide is hinged at its top edge shown as bellow. there is water at the right hand side of gate

  A ships hull is 150m long as has a wetted area of 5000 m2

a ships hull is 150m long as has a wetted area of 5000 m2. when it is encrusted with barnacles it requires 7000 hp to

  What is the temperature of the heat source driving engine

A heat engine operating on the Carnot cycle has an efficiency of 65%. The waste heat from the cycle is rejected to the atmosphere at 20 deg. C. at a rate of 250 kW. What is the temperature of the heat source driving the engine in deg. C? What is the ..

  The charging current must be limited to 20 amps by placing

an automobile battery is modeled as a 12v ideal voltage source in series with a 0.3 ohm internal resistance. it is to

  Diameter high-tension wires

A 10-C wind blows over 6-mm-diameter high-tension wires. Determine the range of velocities over which vortex shedding occurs. Could the shedding frequency be heard?

  Natural gas fired plants at these prices and express the

suppose that coal costs 45ton at the power plant fuel oil costs 60bbl 1 bbl has appoximately 6?106 btu 6 mmbtu and

  Determine final temperature and change in internal energy

100-kg of R-134a at 180kPa are contained in a piston-cylinder device whose volume is 14.715 cubic meter. The piston is now moved until the volume is one half its original sizes. This is done such that the pressure does not change. Determine the final..

  Find the x-component of the vector a -b for the previous

two vectors a with magnitude 32.0 units directed at an angle of 56.0 deg above the x-axis and b 32.0 units long

  Determine the systems coefficient of performance the power

an ideal vapor compression refrigeration cycle that uses r-134a maintains a pressure in the condenser of 1000kpa and

  Determine the rate of steam flow-back-pressure steam

A 20 MW back-pressure steam turbine receives steam at stagnation pressure of 4 MPa and stagnation temperature of 300oC, exhausting from the last stage at stagnation pressure of 0.35 MPa. The turbine isentropic efficiency is 0.884, and mechanical loss..

  What are different types of nuclear reactors

What are different types of Nuclear reactors in operation in thev world.

  A syringe has diameter d 4 cm and its piston is pressed

a syringe has diameter d 4 cm and its piston is pressed with the force f 30 n. find the maximum velocity of the water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd