Corresponding substances or spaces for a air-conditioner

Assignment Help Mechanical Engineering
Reference no: EM13704752

Heat is transferred from a stream of water to the refrigerant in the evaporator, and from the refrigerant to another stream of water in the condenser. In a household refrigerator, from what substance or space does the refrigerant reject heat in the condenser? What are the corresponding substances or spaces for a air-conditioner?

Reference no: EM13704752

Questions Cloud

Calculate the velocities of the water at the two holes : There are two holes in the side of a bucket, one is 10 cm below the surface, and the other is 20 cm below. Calculate the velocities of the water at the two holes
Estimate the charge on each capacitor : Given a 2.75 µF capacitor, a 3.75 µF capacitor, and a 9.00 V battery, Find the charge on each capacitor if you connect in series across the battery
Find the brick inner surface temperature : Hot combustion gases of a furnace are separated from the ambient air and its surroundings, which are at 25 C, by a brick wall that is 0.15m thick. The brick has a thermal conductivity of 1.2 W/mK and a surface emissivity of 0.8.
Coefficient of performance of a refrigeration cycle : The efficiency of a refrigerator is given by the coefficient of performance (COP). Write two different expressions for the COP of a refrigeration cycle; one in terms of heat transfer and work input, and the other in terms of heat transfers only.
Corresponding substances or spaces for a air-conditioner : Heat is transferred from a stream of water to the refrigerant in the evaporator, and from the refrigerant to another stream of water in the condenser. In a household refrigerator, from what substance or space does the refrigerant reject heat in the c..
Diffusion in liquids commonly assumed a rigid sphere : Diffusion in liquids commonly assumed a rigid sphere in a continuum. When would this model be most accurate?.When could it fail? Diffusion varies with viscosity to the (+1) power in gases but to the (-1) power in liquids. Why?
Back-pressure steam turbine receives steam : A 20 MW back-pressure steam turbine receives steam at stagnation pressure of 4 MPa and stagnation temperature of 300oC, exhausting from the last stage at stagnation pressure of 0.35 MPa. The turbine isentropic efficiency is 0.884, and mechanical loss..
Volume of the container and the volume of the liquid phase : A container holds 10 kg of water at 130 *C with a quality of 4. What is the pressure in the container, the volume of the container, and the volume of the liquid phase?
Large hydraulic cylinder with a piston diameter : You have a large hydraulic cylinder with a piston diameter of 8.00 inches. The rod of the cylinder is extended 48 inches. The pressure inside the cylinder at time, t = 0.00 sec is 1,000 psig. There is a 10 foot long hose connected to the hydraulic cy..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the percent span for the old and new setpoints

a reactor setpoint wasincreased from 160 psig to 190 psig. the reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig. what is the percent span for the old and new setpoints?

  Determine the magnitude of the radial component of force

the planar motion of a 0.5 kg particle is defined by the equations r6t2m and thetat rad where t is in seconds.

  Olympic champion usain bolt of jamaica holds the world

olympic champion usain bolt of jamaica holds the world record for running 100 meters in 9.58 seconds. if his reaction

  Assume a wind turbine with a hub 50 meters above the ground

assume a wind turbine with a hub 50 meters above the ground a rotor diameter of 50 meters and wind conversion efficiecy

  Show the process on a t-v diagram label axes with respect

one kilogram of ammonia initially saturated vapor at -4degc undergoes a constant volume process to a final pressure of

  An otto cycle has the lowest t as 520 r and the lowest p as

an otto cycle has the lowest t as 520 r and the lowest p as 12 psi. the highest t is 4500 r and combustion adds 500

  A shaft with a diameter of 100 mm rotates at 1500 rpm a

a shaft with a diameter of 100 mm rotates at 1500 rpm. a fluid-film bearing is designed to support a 5 kn load. assume

  Find the centroid and moment of inertia ix of a composite

find the centroid and moment of inertia ix of a composite steel structure. the structure is built out of a 2 thick by

  Consider 4 power transistors each dissipating 15 w are

consider 4 power transistors each dissipating 15 w are mounted on a thin vertical aluminum plate 22 cm x 22 cm in size.

  Water is boiled at 1 atm pressure in a 25-cm-internal-

water is boiled at 1 atm pressure in a 25-cm-internal- diameter stainless steel pan on an electric range. if it is

  Exiting stream 3 is at 079 mpa and is know to contain a

high pressure steam steam 1 at a rate of 1000kgh initially at 3.5 mpa and 350 c is expanded in a turbine to obtain

  Calculate the critical crack tip radius for a ceramic

calculate the critical crack tip radius for a ceramic material that has a flexural strength of 638 mpa an elastic

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd