Convert the twos compliment numbers to decimal

Assignment Help Electrical Engineering
Reference no: EM13254144

Convert the following Two's Compliment numbers to decimal:

1) 0101 1110 10112C
2) 1001 1111 10002C
3) 1111 1111 11112C
4) -1001 0110 10012C
5) 1010 1010 10102C
6) 1000 0000 00002C

Reference no: EM13254144

Questions Cloud

Compute average cycle time and normal time for each element : Compute the average cycle time and normal time for each element. Then calculate the standard time for the entire task.
Discuss the concept of type conversion in C : Discuss the concept of type conversion in C. Why do we need type conversion and what is the use of the Cast Operator? What is the effect of using the cast operator both on an expression and on a single variable?
Find the potential differences across the inductor : A 24.0V battery is in series with a switch, a 0.30Hinductor, and a 24? resistor. Find the potential differences across the inductor at t=3
What is the production for each alternative : What is the production (output per hour) for each alternative? What is the productivity (output per labor hour)?
Convert the twos compliment numbers to decimal : Convert the following Two's Compliment numbers to decimal: 1) 0101 1110 10112C 2) 1001 1111 10002C 3) 1111 1111 11112C 4) -1001 0110 10012C  5) 1010 1010 10102C 6) 1000 0000 00002C
Calculate the economic order quantity : Calculate the annual holding cost plus the annual ordering cost to get the total annual cost when using an order quamtity of 200 boxes. Please show your work.
Preparing for contract negotiations : You are preparing for contract negotiations. To achieve your desired contract negotiation results, you need not only a strategy but also tactics and countertactics.
Subnet masking and designing small networks : Users on wireless or the open nodes adjacent to the concierges desk should not be able to access the hotels corporate networks and corporate network should only be able to talk to the machine room using protocols DNS, DHCP, HTTP, HTTPS and SSH.
What are major components of a strategic management process : What are the major components of a strategic management process? Which component is most difficult for managers to perform? Explain your answer.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain in detail on the fabrication process of the finfet

Explain in detail on the fabrication process of the FINFET. You must show a 3-dimensional view of FINFET and label the its L and W, the length and width of the gate.

  What is the restriction on enable control input lines

What is the function of the enable control input of a tri-state buffer If the output of two or more tri-state buffers is connected to each other, what is the restriction on enable control input lines

  What is the actual power being dissipated by the circuit

A 20V voltmeter with a sensitivity of 10,000 ohms / volt rating and a 5A ammeter are used to measure the power being dissipated in a dc circuit. The voltmeter reads 13V and the ammeter 2.1A.

  Identify the minimum logic implementation of js and ks

Construct a truth table for the state machine showing all possible states and the logic solution using J-K flip-flops. Construct K-maps for the J-K solutions, identify the minimum logic implementation (circle groups on K-maps), and write equations f..

  Determine an equation for angular velocity

If the battery is replaced with a 6 Volt battery it was experimentally determine that the no load speed is reduced to 120 rpm. For this situation, determine a new equation for angular velocity,(in rad/sec) versus Torque (in Nm).

  Describe bandpass filters with any center frequency

an Armstrong indirect FM modulator to generate an FM carrier with a carrier frequency of 96 MHz and deviation of f=20 KHz. A narrowband FM generator with Fc=200 KHz and adjustable deviation f in range of 9 to 10 Hz is available.

  A radio receiver for the hf band covers the frequency

A radio receiver for the HF band covers the frequency range 2 MHz to 30 MHz. The first IF frequency is 3.0 MHz and the local oscillator is above the received signal frequency.

  Why the code should branch to the line that monitors pb4

Bit 4 of Port B is connected to a switch that normally outputs a zero. Monitor this switch to detect a change from zero to one. Immediately when it becomes one, call a function to toggle Bit 5 of Port B, which is connected to an LED

  Estimate the worst-case varation in film thickness

A wafer 100mm in diameter is mounted in an electron-beam evaporation system in which the spherical radius is 40cm. Use Eq. 6.7 to estimate the worst-case varation in film thickness between the center and edges

  Calculate armature current and total losses in the machine

A 240kW 500 Volt 1750rpm separately excited dc generator has an overall efficiency of 94%. The shunt field resistance is 60ohms, and the rated current is 5amps. The I^2R loss in the armature is 0.023pu.

  Determine the atomic radius of a single aluminum atom

aluminum has the FCC crystal structure. Its atomic weight is 26.98g/mole, and its density is 2.70g/cm3. Determine the atomic radius of a single aluminum atom.

  What is the time-bandwidth product in the case

A radar transmits a monotone pulse of 5-s duration. Suppose the radar were redesigned so that the same pulse envelope is frequency modulated with linear FM over 100 MHz. (a) What is the possible new range resolution

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd