Convective heat transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13706999

An aluminium casting 2 cm cubed is at 800 degrees Celsius and is to be air quenched in 30 degree Celsius air having convective heat transfer coefficient of 50 W/m^2*k determine

a. biot number

b. time constant

c. time for casting to cool to 100 degrees Celsius

Reference no: EM13706999

Questions Cloud

The volume of the 8-foot-wide portable storage container : The volume of the 8-foot-wide portable storage container shown below is given by the expression (72x^2+120x-400) ft^3. If it's dimensions can be determined by factoring the expression, find the height and the length of the container.
Birth control in latin america : Writing Longer Argumentative Passages Introduction, Birth Control in Latin America
Determine the final temperature and the heat transfer : Nitrogen in a closed tank initially at 27 0C is contained in a rigid closed tank is heated until the pressure doubles. Assuming an ideal gas, determine the final temperature and the heat transfer.
What is the energy recoverable as heat per decay in mev : An alpha-emitter, has been used as a thermal power source, as described in Table 12.2. What is the energy recoverable as heat per decay in MeV? Provide two answers, one assuming all of the energy produced is dissipated as heat, and one assuming only ..
Convective heat transfer coefficient : An aluminium casting 2 cm cubed is at 800 degrees Celsius and is to be air quenched in 30 degree Celsius air having convective heat transfer coefficient of 50 W/m^2*k determine
Determine the radiation per unit area in the bandwidth : Determine the radiation per unit area in the bandwidth of 1 micrometer to 2.5 micrometer in W/m^2 from a balck body at 2500 K.
What statically deflection must the isolators : An aircraft radio weighing 106.75 N is to be isolated from engine vibrations ranging in frequencies from 1600 to 2200 cpm. What statically deflection must the isolators have for 85% isolation?
Assuming ideal gas behavior of the air : 10 ft3 of air initially at 550 0R, 100 psi undergoes a polytropic process pV1.2 = constant to a final pressure of 50 psi. The work of the process is 100 Btu. Assuming ideal gas behavior of the air, determine (a) the mass of air in lb, (b) the final v..
Find the magnitude of the force that unknown charge exerts : A charge of -0.600microColoumbs exerts an upward 0.250N force on an unknown charge 0.250m directly below it. What is the magnitude of the force that the unknown charge exerts

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A heat engine in each cycle absorbs energy from a reservoir

a heat engine in each cycle absorbs energy from a reservoir as heat and does an equivalent amount of work with no other

  A certain ceramic has a fracture toughness of kic of 5

a certain ceramic has a fracture toughness of kic of 5 mnm32. a batch of samples of this material contains surface

  Determine the heat generation rate of the portable heater

a portable heater is placed inside a laboratory chamber to maintain the inside air temperature of the chamber at

  Find the steady spped of the block assume the velocity

a block of mass 10 kg and measuring 250 mm on each edge is pulled up an inclined surface on which there is a film of

  Metal alloy has body centered cubic crystal structure

A certain metal alloy has body centered cubic crystal structure; it has an average atomic weight of 71.2 amu; and the metal has an average atomic radius of 0.131 nm. Determine the theoretical density of this metal in grams per cubic centimetre.

  Consider a viscoelastic polymer rod that is stretched from

consider a viscoelastic polymer rod that is stretched from 100 mm to 165 mm by a stress of 3.35 mpa. while being held

  What will be the approximate density of the boat hull

A group of mechanical engineers like catamaran sailing on the Great Salt Lake and decide to use a glass-fiber reinforced composite with a high fiber fraction for a new boat design. The composite is 60 volume % SiO2 glass fibers and the remainder is a..

  If a torque of m2001-e-02tnm where t is in seconds is

gears a and b have a mass of 50kg and 15kg respectivly. their radii of gyration about their respective centers of mass

  The bullet gets stuck in the block initially both blocks

two block masses on smooth wheels m1 and m2 are connected to the wall through spring having a spring constant of k2

  On an overflow structure of 50 degrees slope the water

on an overflow structure of 50 degrees slope the water depth measured normal to the surface of the structure is 1.2 m 4

  Determine the reduction in the exit temperature of the

the compression stages in the axial compressor of the industrial gas turbine are close coupled making intercooling very

  What volumetric flow rate of fuel gas is required

What volumetric flow rate of fuel gas is required if there are no heat losses to the surroundings?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd