Consider ideal regenerative rankine cycle for power plant

Assignment Help Mechanical Engineering
Reference no: EM13702446

Consider the ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feed water heater (FWH) can be neglected, there are no pressure drops in the boiler, condenser, and FWH, and the steam leaves the condenser and FWH as saturated liquid.

a) Sketch the T vs. s cycle/diagram for this ideal Rankine power plant (including the T vs. s bell-curve for water/steam and the exact values of P & v at each stage).

b) Sketch the P vs. v cycle/diagram for this ideal Rankine power plant (including the P vs. v bell-curve for water/steam and the exact values of P & v at each stage).

c) What is mass flow rate at stages 6 & 7?

d) How much heat input (to the boiler) is needed in 10 seconds?

e) What is the net rate of work output? (I suggest you first make a table of s, P, h, v, T, mass flow rate , & x for each stage of the cycle. You will need to use tables A4, A5, A6, & A7 in the appendix.)

Reference no: EM13702446

Questions Cloud

Does company culture impact security : Does company culture impact security? If so, in what way? How does this fit into computer ethics?
Fins for heat recovery : An inventor wants to increase the efficiency of wood burning stoves by reducing the energy lost through the exhaust stack. He proposes to accomplish this by attaching fins to the outer surface of the chimney, as shown schematically below.
Adiabatic turbine system to generate electricity : Steam is used in the following adiabatic turbine system to generate electricity; 15% of the mass flow from the first turbine is diverted for other use. How much work (in kJ/h) is generated by the first turbine which is 80% efficient?
Five pounds of propane have a volume : Five pounds of propane have a volume of 1 ft3 and a pressure of 600 psi. Determine the temperature (in °R) using each of the following methods.
Consider ideal regenerative rankine cycle for power plant : Consider the ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feed water heater (FWH) can be neglected, there ar..
A simple gear train with spur gears that contains a pinion : A simple gear train with spur gears that contains a pinion, an idler, and a gear utilized in order to transmit 10 hp using a train ratio of 4.5:1. The pinion has 14 teeth and the idler has 30 teeth. The input shaft operates at 2000 rpm. The pressure ..
Aerodynamic drag first exceed the rolling resistance : Consider a car having a frontal are of 2.0m^2 with a drag coefficient of 0.35. The mass of the car is 1250kg and the rolling resistance is 1.0% of the weight of the car. At what speed does the aerodynamic drag first exceed the rolling resistance.
A weak base that reacts with water according to the equation : Methylamine, CH3NH2, is a weak base that reacts with water according to the equation above. A student obtains a 50.0 mL sample of a methylamine solution and determines the pH of the solution to be 11.77.(a) Write the expression for the equilibr..
A 32.50-mg sample of naturally occurring elemental silicon : A 32.50-mg sample of naturally occurring elemental silicon was irradiated with neutrons in a nuclear reactor at a flux density of 2.75E-13 thermal neutrons per (cm^2 sec). The activity of 31-Si was determined at a remote site with a beta parti..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the ratio of the original and etched crack tip

the fracture strength of glass may be increased by etching away a thin surface e layer. it is believed that the etching

  The end of the lever arm moves 50cm and the load moves 20cm

in a system a lever needs and effort of 200n to lift a load of 350n. the end of the lever arm moves 50cm and the load

  A particle travels along a straight line with an

a particle travels along a straight line with an acceleration of a 10-0.2s ms2 where s is measured in meters.

  Draw and dimension the bar diagram for a 3 38 in shaft with

draw and dimension the bar diagram for a 3 38 in. shaft with a class 3 fit. draw and dimension a typical hole and shaft

  If the cycle operates on a stationary mass of 1 kg of water

in a carnot cycle heat is supplied at 350degc and rejected at 27degc. the working fluid is water which while receiving

  A cylinder containing a mixture of 90 n2 and 10 c2h6 and a

cylinder containing ch4 c2h6 and n2 has to be prepared in which the ratio of the moles of ch4 to c2h6 is 1.3 to 1.

  An electric heater in the form of a horizontal disk of 57

an electric heater in the form of a horizontal disk of 57 mm diameter is used to heat the bottom of a tank filled with

  What is the efficiency of a carnot cycle running between

a heat engine is composed of of a monatomic ideal gas which runs in the following cycle at point a the pressure is 3

  Draw a system diagram and label all the components number

consider a rankine cycle 100 mw net power vapor power plant with a reheater and regeneration and a single open

  A radiation detector having a sensitive area of

a radiation detector having a sensitive area of ad4times10-6 m2 is configured to receive radiation from a target area

  The cylinder piston and rod diameters are 508 and 255

this system has a hydraulic cylinder with a suspended load of 0 which is removed. the cylinder piston and rod

  All test specimens were 15 inches in diameter and 3 inches

on a grap paper draw the mohrs circle of stress for a uniaxial test and two triaxial test in which the maximum

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd