Consider the heating of an incompressible fluid with

Assignment Help Mechanical Engineering
Reference no: EM13631205

Consider the heating of an incompressible fluid with velocity Um inside a thin - walled tube. The diameter of the tube is D. Heating is in the hydrodynamically and thermally developed region and the flow is laminar. Incompressible fluid enters the tube at temperature T1 and pressure P1. The tube length of the tube is L. Heating can be done either by condensing steam on the outer surface of the tube, thus maintaining a uniform surface heat flux. Calculate the irreversibility for both of these heating conditions by assuming fluid properties are constants. Discuss.

Reference no: EM13631205

Questions Cloud

The red light emitted by a helium-neon laser has a : the red light emitted by a helium-neon laser has a wavelength of 632.8 nm. what is the frequency of the light
A diesel cycle with compression ratio of 18 operates on air : a diesel cycle with compression ratio of 18 operates on air with a low pressure of 200kpa and a low temperature 200c .
Find the force exerted on an electron at this point moving : a very long thin rod carries electric charge with the linear density 28.0 ncm. it lies along the x axis and moves in
A compressive force of 100kn is applied to one side while a : a brass cube e100 gpa v 0.25poissons ratio is 100 mm long per side. a compressive force of 100kn is applied to one
Consider the heating of an incompressible fluid with : consider the heating of an incompressible fluid with velocity um inside a thin - walled tube. the diameter of the tube
Stray heat transfer from the heat exchanger may be : consider an air-water heat exchanger. air flowing steadily at the rate of 0.5 kgs enters the heat exchanger at 100 kpa
Two forces p and q are applied as shown at point a of a : two forces p and q are applied as shown at point a of a hook support knowing that p 15n and q 25n determine
A 0210-a current is charging a capacitor that has circular : a 0.210-a current is charging a capacitor that has circular plates 15.8 cm in radius. the plate separation is 4.00 mm.a
A hair dryer consumes 1200w of electric power when running : a hair dryer consumes 1200w of electric power when running the inlet volume flow rate and the exit velocity of air are

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Using cv constant theory an using thermal properties at

in a diesel cycle the cutoff ratio is two and the compression ratio is eighteen. at state 1 the air is 14.7 psia and

  Asolute pressure is known at both inlet and outlet

water flows in a horizontal pipe with entrance velocity 2.5ms is turning 90 degrees and leaves the pipe. pipe diameter

  Assume macrs depreciation for the special tools and a 39

the profitable palmer golf cart corp. is considering investing 300000 in special tools for some of the plastic golf

  A pure aluminum conical section with cross sectional

a pure aluminum conical section with cross sectional diameter of d ax12. a 0.5meters12. the small end of the cone is

  Required gusset plate and thickness for the tensile

1. for the connection shown in figure assuming the bolts are frac34- in. diameter and the angle and plate astm a36

  A random sample of 15 parts shows mean diameter 0742 inch

1. assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with

  Compute the placement of the last intermediate anneal so

copper is being reduced from a hot rolled 38 in diameter rod to a final diameter of .1 in. by wire drawing through a

  During a test it is found that this represents 28 of the

a power station output is 500 megawatts. during a test it is found that this represents 28 of the energy put into the

  Consider a large classroom on a hot summer day with 150

consider a large classroom on a hot summer day with 150 students each dissapating 60w of sensible heat. all the lights

  An irregularly shaped object weighs 100 lb in air and 64

an irregularly shaped object weighs 100 lb in air and 64 lb when fully submerged in water. determine the volume and

  During this process heat is transferred to the system to

a rigid tank 0.4 m3 contains air at 400 kpa and 30c and is connected by a valve to a piston-cylinder device with zero

  Calculate the pressure of air inside the cylinder before

a well-insulated vertical piston-cylinder device contains air. the diameter of the piston is 8 inches. atmospheric

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd