Consider the element platinum which has an atomic radius of

Assignment Help Mechanical Engineering
Reference no: EM13625669

1. Consider the element platinum, which has an atomic radius of 0.139 nm and a room temperature density of 21.45 g/cm3.
a. Determine the atomic packing factor for this element.
b. In a sketch of the structure, locate the tetrahedral and octahedral interstices.
c. What is the diameter of the largest atom that can fit in the tetrahedral interstices of this structure?

Reference no: EM13625669

Questions Cloud

Estimate the minimum runway length and time needed to reach : a fully loaded boeing 777-200 jet transport aircraft weighs 325000 kg. the pilot brings the 2 engines to full takeoff
A teacher plans to construct a 25 question exam from : a teacher plans to construct a 25 question exam from previous exams in which there are 50 true false questions and 80
Find all the medians for the binomial distribution with : find all the medians for the binomial distribution with parameters bin5
When the cylinder reaches the bottom of the ramp what is : when the cylinder reaches the bottom of the ramp what is its total kinetic energy?when the cylinder reaches the bottom
Consider the element platinum which has an atomic radius of : 1. consider the element platinum which has an atomic radius of 0.139 nm and a room temperature density of 21.45 gcm3.a.
Someone claims that bergen county high school students on : someone claims that bergen county high school students on average score higher on the sat than high school students
It is desired to compare the results of property : it is desired to compare the results of property predictions for water near or in the saturation region using a the
A series rcl circuit includes a resistance of 281 an : a series rcl circuit includes a resistance of 281 an inductive reactance of 860 and a capacitive reactance of 606. the
In a study of the relationship between pet ownership and : in a study of the relationship between pet ownership and physical activity in older adults 594 subjects reported that

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the acceleration of the fluid particle located at

the velocity field for a fluid particle is described by the equation given below. determine the acceleration of the

  Two charges -18 c and 49 c are fixed in place and separated

two charges -18 c and 4.9 c are fixed in place and separated by 4.2 m. a at what spot along a line through the charges

  The inlet and outlet diametersof the nozzle are20 mm and10

superheated steam enters a nozzleat 0.13 mpaand 600 k and exits at 0.1 mpa. heat interactions and frictional effects

  Assume 35 of fuel nitrogen converts to no and that fuel no

a 825 mw electric power plant 36.2 efficient uses a coal with the following composition c 74.8 wt h 5.2 wt o 7.3

  Calculate the maximum permissible crack size

calculate the maximum permissible crack size in acenter cracked panel subjected to a unifrom stress of 20 ksi. the toughness is 50 ksi"in, the yield stress is 60 ksi, w=12 inches

  Stoichiometrically how many kg of methanol are required for

biodiesel is produced from vegetable or animal oils. usually the glycerine in the oil is replaced by methanol. since

  Find the mass in both a and b

The piston is now unlocked so it is free to move, and it conducts heat so the air comes to a uniform temperature . Find the mass in both A and B, and the final T and P.

  Consider a steam power plant with reheat that operates on a

consider a steam power plant with reheat that operates on a modified rankine cycle. steam enters the high-pressure

  The water level in the dam is upto the brim of the wall

one of the walls of a dam is at 67 degrees to the horizontal. the wall is 8 m long and 40 m wide. density of the water

  If a torque of m2001-e-02tnm where t is in seconds is

gears a and b have a mass of 50kg and 15kg respectivly. their radii of gyration about their respective centers of mass

  Calculate the pressure of air inside the cylinder before

a well-insulated vertical piston-cylinder device contains air. the diameter of the piston is 8 inches. atmospheric

  You are working in a company that has developed a process

you are working in a company that has developed a process to produce dna vaccines from e.coli. after the fermentation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd